Products in Composite Materials: Prepreg

TG43/5 is a B-staged epoxy prepreg based on a fine weave glass fabric suitable for the manufacture of tubes and laminates.

HexPly® M77 is a fast curing hotmelt, thermosetting epoxy resin matrix, specifically designed for prepreg applications at which short cure cycles are required. M77 is recommended for curing at 120 – 150°C and is suitable for a range of pressures (5 – 35bar). M77 can be used for manufacture of large industrial components, suitable for cure of thin and thick sections.

AX-3201XL is an Epoxy Fiberglass Prepreg for Vacuum Bag Only Processing.

Toray Toray AmberTool® HX56 is a low temperature curing epoxy composite tooling prepreg. After a suitable post cure, an end use temperature of 180°C (356°F) is achieved. Toray AmberTool® HX56 achieves an excellent surface finish for small to medium sized autoclave tooling.

TU300 is a polyetherketoneketone (PEKK) fiber-reinforced uni-directional tape that processes in the 675-725oF (360-385oC) temperature range. The prepreg is used in a variety of high performance, structural composite applications. PEKK is a high temperature semi-crystalline polymer with a good combination of toughness, chemical and solvent resistance, low moisture absorption and superior FST properties.

HexPly® 1454 is a self-extinguishing epoxy resin system with very high self adhesion properties. It has good handling and is tolerant of a wide range of processing conditions. HexPly® 1454 is ideal for the fabrication of honeycomb sandwich structures when high peel strength and good impact properties are required. HexPly® 1454 prepregs are only available with fabric reinforcements.

AX-5611 is a MDA-free condensation Polyimide Carbon Prepreg.

HexPly® M21 is a high performance, very tough epoxy matrix for use in primary aerospace structures. It exhibits excellent damage tolerance, especially at high energy impacts. HexPly® M21 is a toughened epoxy resin system supplied with unidirectional or woven carbon or glass fibers. HexPly® M21 was developed as a controlled flow system to operate in environments up at 121°C (250°F).

7146 PTFE-Glass Fabric is a Economy Grade PTFE-Glass Fabric is designed for large volume applications that require cost-efficiency and high performance. Applications include leaders for processing paper, plastics, metallic foils and cloth, separator sheets for processing uncured rubber and manufacturing of abrasive wheels.

Toray BTCy-2 is our lowest dielectric cyanate ester prepreg resin system. This resin system is valued in high-energy microwave Applicationss due to the low loss tangent. 177°C (350°F) Cure Cyanate Ester

IM Carbon Fiber UD150H60-MR70 is a E3 Matrix System with a precursor as PAN.

AX-4300 is a High Temperature Phenolic Laminating Aramid Prepreg.

Deltapreg DT121R is a Automotive, Sports and Leisure, Life innovation with Exterior and Interior Application.

HexPly® 954-3 is a 350ºF (177ºC) curing cyanate resin with excellent resistance to moisture absorption, outgassing and microcracking. HexPly® 954-3 is formulated for autoclave or press molding using a standard cure of two hours at 350ºF (177ºC). Glass transition temperature can be maximized by post curing at 450ºF (232ºC). The recommended lay-up procedure is HSP-L3. The recommended cure procedure is HSP-C1 or HSP-C2.

PolyWeb C is made from polypropylene or PET staple fiber and chopped fiberglass (natural or black).

SIMPREX® H425-200 is an advanced vinyl ester prepreg designed to provide excellent fire retardance properties (V-0 flammability rating). It is ideal for manufacturing sandwich structures, providing good adhesion to core materials such as Nomex® honeycomb, balsa and foams. SIMPREX® H425-200 is a great choice for many applications in the range of low to medium service temperature, where a high degree of fire retardance is required.

PRF Composite Materials RP800 is an epoxy tooling prepreg system capable of withstanding temperatures up to 190°C after full post cure. RP800 is available in carbon and glass woven fabrics from 200 - 800 g/m2 impregnated with epoxy resin. RP800 prepreg allows high quality tooling laminates to be produced directly from a low temperature master model permitting a wide choice of master model materials. Using a low temperature vacuum bag and autoclave process for inital cure, the tool laminate can then be demoulded for freestanding post cure.

TU400 is a polyetherimide (PEI) fiber-reinforced uni-directional tape that processes is in the 660-710oF (350-375oC)temperature range. The prepreg is used in a variety of high performance, structural composite applications. PEI is an amorphous polymer that provides high temperature resistance, toughness and superior FST properties.

ACP Composites 8.8 oz Fiberglass 8-Harness Satin Weave RTS Prepreg is a Satin Weave EGlass fabric impregnated with a thermosetting epoxy resin system. . It is storable at room temperatures and does not require freezer storage. With the long out life of the resin matrix, the carbon fiber prepreg can be shipped and handled at room temperatures. It is ideal for use when a long shelf life is desired, high-temperature capabilities are not required and controlled resin content is wanted.

Electroglide® is an epoxy-based composite surfacing film with embedded metal mesh that is designed to protect aircraft composite parts from lightning strikes.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

MTC450 prepreg is toughened for demanding applications and is designed for high service temperatures, giving great flexibility in component manufacture. It can be supplied on a variety of fabrics and in UD format to meet your cost and manufacturing requirements.

Lectromat Glass Cloth and Mats WG-204 is applied in permanent magnet bonding.

AtenPly CPPS35 are thin sheets of continuous reinforcement fibers impregnated with thermoplastic resin. It is made direct from the fiber roving and thermoplastic melt using proprietary technology developed by Jonam Composites Ltd. This cost-effective efficient process produces light weight, high-strength ,well impregnated, smooth tape with unidirectional fiber reinforcement.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

PRF Composite Materials RP801 is an epoxy tooling prepreg system capable of withstanding temperatures up to 190°C after full post cure. RP801 is available in carbon and glass woven fabrics from 200 - 800 g/m2 impregnated with epoxy resin. RP-801 prepreg allows high quality tooling laminates to be produced directly from a low temperature master model permitting a wide choice of master model materials. Using a low temperature vacuum bag and autoclave process for inital cure, the tool laminate can then be demoulded for freestanding post cure.

Park’s E-752-MTS is a toughened; 350°F cure epoxy system designed with improved mechanical properties and damage tolerance that is suitable for primary aircraft structures. Consistent with the E-752 family of epoxies, the E-752-MTS allows flexible and robust processing in Autoclave, Out of Autoclave and Press cures. It exhibits improved toughness and impact strength while maintaining good tack and drapeability for ease of layup.

Resinoid 1328 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for applications requiring exceptional tensile strength such as grinding wheels. Resinoid 1328 exhibits excellent electrical and thermal properties as well as dimensional stability. This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

APCM SG 4528-029CU-102V is a medium weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

IM Carbon Fiber UD150H60-T800 GRADE is a E3 Matrix System with a precursor as PAN.

NMG Composites CPT-12K is an intermediate material of a composite material, which is made of carbon fiber yarn, resin matrix, release paper and other materials through coating, hot pressing, cooling, laminating, coiling and other processes, also known as carbon fiber prepreg with Plain woven, 12K Conbon fiber Prepreg.

LTC150 Prepreg is designed to cure in a lower time at low temperatures than standard tooling prepregs whilst giving the potential for high temperature tooling. It can be supplied on a variety of fabrics to meet your cost and manufacturing requirements.

7069 PTFE-Glass Fabric is a Premium Grade PTFE-Glass Fabric offers optimum release and durability in harsh environments. Applications include reusable pan liners for cooking and baking, laminate separator sheets, tortilla and pizza crust belts, heat sealing and applications where fabric weave impression is undesirable.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

HexPly® M77CS is a fast curing hotmelt, thermosetting epoxy matrix, specifically designed for prepreg applications at which short cure cycles and clear surfaces are required. M77CS is recommended for curing at 120 – 150°C and is suitable for a range of pressures (5 – 35bar). M77CS can be used for manufacture of industrial components with a clear surface.

SIMPREX® M850 is an advanced vinyl ester prepreg designed to provide a high performance-to-cost ratio. SIMPREX® M850 has a medium to high tack and provides good adhesion to core materials such as Nomex® honeycomb, balsa and polyurethane foam. It is a great choice for many applications in the range of low to medium service temperature.