Products in Consumer Goods: Prepreg

IM Carbon Fiber UD200H60-T1000 GRADE is a E3 Matrix System with a precursor as PAN.

Unidirectional belt G Tape - GT uses continuous fiber as the reinforcing material and thermoplastic resin as the base material to form a high-strength, high-impact, fully recyclable composite material through the corresponding infiltration process.

7069-TW-GRN PTFE-Glass Fabric is a Premium Grade PTFE-Glass Fabric offers optimum release and durability in harsh environments. Applications include reusable pan liners for cooking and baking, laminate separator sheets, tortilla and pizza crust belts, heat sealing and applications where fabric weave impression is undesirable.

HexPly® 924 is a controlled flow epoxy matrix developed for the fabrication of high temperature resistant primary structures. When cured, HexPly® 924 becomes a tough composite with high impact resistance and damage tolerance. It is particularly suitable for aircraft primary structures and elevated temperature applications such as performance cars.

PRF Composite Materials RP803 is formulated to provide an initial cure cycle of either 12 hours at 60°C or 6 hours at 70°C and extended out life of 9 days at 20°C. The system is capable of withstanding temperatures up to 190°C after full post cure. RP803 is available in carbon and glass woven fabrics from 200 - 800 g/m2 impregnated with epoxy resin. RP803 prepreg allows high quality tooling laminates to be produced directly from a low temperature master model permitting a wide choice of master model materials. Using a low temperature vacuum bag and autoclave process for inital cure, the tool laminate can then be demoulded for freestanding post cure.

Ecotechnilin L-FLAXPREG-T-UD-110-36m² is a unidirectional (UD) fibers - FLAXPREG T-UD 70.

Evopreg® ampliTex™ – Carbon Hybrids can be combined with traditional carbon fiber-epoxy prepregs to produce a high performance hybrid offering the benefits of both materials. By replacing carbon bulking plies with flax, it is possible to produce a “thin sandwich” structure that retains the bending stiffness of an all-carbon laminate, whilst also delivering the weight reduction, vibration damping and reduced environmental impact that flax offers.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

Resinoid 1328 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for applications requiring exceptional tensile strength such as grinding wheels. Resinoid 1328 exhibits excellent electrical and thermal properties as well as dimensional stability. This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

IM Carbon Fiber UD150H60-T800 GRADE is a E3 Matrix System with a precursor as PAN.

PRF Composite Materials RP801 is an epoxy tooling prepreg system capable of withstanding temperatures up to 190°C after full post cure. RP801 is available in carbon and glass woven fabrics from 200 - 800 g/m2 impregnated with epoxy resin. RP-801 prepreg allows high quality tooling laminates to be produced directly from a low temperature master model permitting a wide choice of master model materials. Using a low temperature vacuum bag and autoclave process for inital cure, the tool laminate can then be demoulded for freestanding post cure.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

AtenPly CPPS35 are thin sheets of continuous reinforcement fibers impregnated with thermoplastic resin. It is made direct from the fiber roving and thermoplastic melt using proprietary technology developed by Jonam Composites Ltd. This cost-effective efficient process produces light weight, high-strength ,well impregnated, smooth tape with unidirectional fiber reinforcement.

LTC150 Prepreg is designed to cure in a lower time at low temperatures than standard tooling prepregs whilst giving the potential for high temperature tooling. It can be supplied on a variety of fabrics to meet your cost and manufacturing requirements.

7069 PTFE-Glass Fabric is a Premium Grade PTFE-Glass Fabric offers optimum release and durability in harsh environments. Applications include reusable pan liners for cooking and baking, laminate separator sheets, tortilla and pizza crust belts, heat sealing and applications where fabric weave impression is undesirable.

NMG Composites CPT-12K is an intermediate material of a composite material, which is made of carbon fiber yarn, resin matrix, release paper and other materials through coating, hot pressing, cooling, laminating, coiling and other processes, also known as carbon fiber prepreg with Plain woven, 12K Conbon fiber Prepreg.

IM Carbon Fiber UD200H60-MR60H is a E3 Matrix System with a precursor as PAN.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

MTC450 prepreg is toughened for demanding applications and is designed for high service temperatures, giving great flexibility in component manufacture. It can be supplied on a variety of fabrics and in UD format to meet your cost and manufacturing requirements.

APCM DA 4080 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

Resinoid 1371 is a glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for applications requiring prolonged exposure to elevated temperatures andresistance to thermal shocks.This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

HexPly® M10E is an epoxy resin system preimpregnated into aramid, glass or graphite multiaxial fabrics and unidirectional fibers. HexPly® M10E prepregs are recommended for the production of low cost, large thicksectioned industrial structures.

Deltapreg DT124 is a Automotive with structural Application.

Evopreg® EPC200 component prepregs are primarily designed for low-temperature, out-of- autoclave processing. Their flexible cure profile also makes them ideally suited to rapid processing at higher temperatures. Based on a toughened epoxy resin system, Evopreg® EPC200 is formulated specifically for high performance, ease of lay-up and excellent surface finish. The prepregs can be supplied with a range of reinforcement fibers and fabric constructions. They can be consolidated by vacuum bag/oven, autoclave or press molding and are designed for a range of applications including automotive, motorsport, sporting goods and general industrial..

HexPly® F593 is a modified 350°F (177°C) curing epoxy system with very low flow for carbon fabric and tape applications that provides excellent laminate and honeycomb sandwich properties. As a low flow resin, HexPly® F593 lends itself to net resin, zero bleed applications. HexPly® F593’s low flow minimizes sandwich part porosity.

THINPREG™ TP 402 is a resin system suitable for manufacture of unidirectional prepreg material. ThinPreg™ 402 is a versatile system that is used most often with carbon fiber, but can also be impregnated into a wide range of reinforcing fibers including quartz, glass, aramid fiber etc. ThinPreg™ 402 features a high Tg (180°C) capability with additional toughening, and has been designed to be a good all-round product in terms of mechanical strength and processability.

SIMPREX® M940-200 is an advanced vinyl ester prepreg designed to provide a high performance-to-cost ratio. SIMPREX® M940-200 has a medium tack. It can be cured at lower temperature (205°F) and provides good adhesion to core materials such as Nomex® honeycomb, balsa and polyurethane foam. It is a great choice for many applications in the range of low to medium service temperature.

PREGNIT TP-PA has high strength, rigidity and toughness.

MTC811 is a toughened, honeycomb bondable epoxy resin system designed to produce a durable cost effective component with an excellent surface finish. It can be supplied on a variety of fabrics and in UD format to meet your cost and manufacturing requirements.

IM Carbon Fiber UD200H60-MR70 is a E3 Matrix System with a precursor as PAN.

HexPly® 250 is a phenolic matrix widely used in honeycomb sandwich components for aircraft interior furnishings. The low smoke and low toxicity properties of 250 during ignition meet the requirements of FAR 25 and ATS 1000. HexPly® 250 prepreg is available in fabric reinforcements and single tows.

HexPly® M81 is a high performance tough epoxy matrix for use in industrial applications requiring good impact resistance and damage tolerance, such as the automotive industry. HexPly® M81 is based on the highly successful HexPly® 8552 toughened epoxy resin system, used widely around the world for the manufacture of aircraft structures. Non-aerospace customers now have the opportunity to benefit from the excellent performance of this resin system presented with reinforcements specially adapted for industrial markets.

HexPly® 8551-7 is an amine-cured, toughened epoxy resin system supplied with unidirectional graphite fibers. Typical reinforcement is continuous IM7 (intermediate modulus) graphite filaments. HexPly® 8551-7 was developed to operate in a temperature environment of up to 200ºF (93ºC). IM7/8551-7 is an extremely damage-resistant system, recommended for structural applications requiring high strength, stiffness, and damage tolerance. Conventional thermoset resin processing equipment and techniques can be used to process IM7/8551-7 prepreg tape.

Toray RS-1 is an epoxy prepreg resin that provides an excellent balance of mechanical properties, toughness, and modulus. RS-1 has been evaluated and qualified in areas ranging from marine to aerospace and dielectric structures. RS-1 is also available in a lower temperature curing formulation 80°C (176°F).

Natex P-Preg PA11 UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polyamide 11 with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

HexPly 260 is a phenolic resin developed to meet such F.S.T. (Fire, Smoke, Toxicity) regulations and the 1990 O.S.U. index (65/65), for aircraft interior parts as: side wall panels, floor panel, galleys, ceiling panels and lavatories. HexPly 260 prepreg is available in various fabric reinforcements.