Products in Appliances & Electronics: Prepreg

Resinoid 1328 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for applications requiring exceptional tensile strength such as grinding wheels. Resinoid 1328 exhibits excellent electrical and thermal properties as well as dimensional stability. This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.

Natex P-Preg PA11 UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polyamide 11 with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

APCM DA 4092 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

FR408 low dielectric constant (Dk) and low dissipation factor (Df) make it an ideal candidate for broadband circuit designs requiring faster signal speeds or improved signal integrity. FR408 is compatible with most FR-4 processes. This feature allows the use of FR408 without adding complexity to current fabrication techniques.

Resinoid 1345 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for molded electric motor commutators where performance for prolonged periods at elevated temperatures while under centrifugal loads is critical.This material comes in pelletized from and is suitable for injection, transfer or compression molding.

Resinoid 1528 is a glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated for use in automotive applications. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment

Toray 8020 is a new generation of toughened epoxy resin systems offering a balance of mechanical properties and excellent surface finish. The resin system has been developed to offer a long out life and flexible cure schedules and can be applied to a wide range of high performance fibers. Toray 8020 is compatible for co-cure with Toray’s resin film, Toray 8020, and Toray’s syntactic core, Toray MicroPly™ SC8020A.

APCM DA 4082 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

Natex P-Preg PP UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

Resinoid 1550 is a milled glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated at a 2.47 specific gravity. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Natex P-Preg PLA P1/1 950 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

TerraGreen® is engineered for such high-performance applications as power amplifier boards for LTE base stations, internet infrastructure and cloud computing. TerraGreen ® features a Dielectric Constant (Dk) that is stable between -55°C and 125°C, up to 20 GHz. TerraGreen® is a lead-free assembly material and is easy to process. This high-performance material utilizes a short-lamination cycle; the product is easy to drill, does not require plasma desmear, and the prepreg shelf life is similar to FR-4 materials. TerraGreen® is suitable for high-layer count, high-speed digital backplanes and is compatible with Isola’s FR-4 materials for hybrid designs. TerraGreen® meets UL 94 V-0 and is halogen free.

Resinoid 1371 is a glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for applications requiring prolonged exposure to elevated temperatures andresistance to thermal shocks.This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Natex P-Preg PLA UD 800 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

APCM DA 4518 E-Glass is a modified epoxy system coated on heavy weight unidirectional E-Glass fibers. This product is designed to build excellent unidirectional strength using a minimum number of plies. DA 4518/E-Glass Uni also features extended room temperature out time and service temperatures to 300°F.

Toray E731 is a toughened epoxy resin system designed to deliver enhanced resin clarity for cosmetic components within high performance automotive. The resin formulation ensures that components are free from white-spots and exhibit high clarity.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

Toray E721-FR is a modified epoxy resin system of medium viscosity for cures at 120°C (248°F), pre-impregnated into high performance fibers such as carbon, glass, and aramid. Toray E721-FR offers excellent structural properties, flame retardancy, and exceptional toughness allowing direct lamination to honeycomb without the use of resin film. Toray E721-FR is designed for structural Applicationss in the motor racing, marine industries, and for a wide range of engineering Applicationss. If fire-retardant properties are not required, consult separate data sheet for Toray E720.

Resinoid 1365 is a glass reinforced, two-step phenolic molding compound offering excellent mechanical strength as well as good electrical and thermal characteristics. This material is offered as a moderate size pellet suitable for compression and transfer molding. It can be used in injection molding systems with deep flight screws.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

Toray E650 is a low temperature curing toughened resin system pre-impregnated into high performance fibers such as carbon, glass and aramid. It is designed for the production of composite structures in the leisure and sporting industries and also for a range of engineering Applicationss. Toray E650 is compatible for co-cure with Toray’s low temperature cure resin film, Toray EF44, and Toray’s low temperature cure syntactic core, Toray MicroPly™ LT64.

Resinoid 1382 is a glass reinforced, two-step phenolic molding compound formulated for applications requiring exceptional tensile strength. It has been used to replace cast aluminum in certain applications. Resinoid 1382 exhibits excellent dimensional stability, electrical and thermal properties. It is supplied in pelletized form for use in injection, transfer, and compression molding. It can be preformed on automatic equipment.

APCM DA 409U/G35-150 is a tough, versatile, modified epoxy resin prepreg that cures at 250°F, a standard modulus 150 g/m2 carbon prepreg tape which can also be supplied as a 200g/m2 or a 300 g/m2 prepreg.

FR408HR laminate and prepreg products are manufactured with Isola’s patented high performance multifunctional resin system, reinforced with electrical grade (E-glass) glass fabric. This system delivers a 30% improvement in Z-axis expansion and offers 25% more electrical bandwidth (lower loss) than competitive products in this space. These properties coupled with superior moisture resistance at reflow, result in a product that bridges the gap from both a thermal and electrical perspective. The FR408HR system is also laser fluorescing and UV blocking for maximum compatibility with Automated Optical Inspection (AOI) systems, optical positioning systems and photo-imageable solder mask imaging.

SIMPREX® 1455 are advanced vinyl ester prepreg designed to provide high strength and toughness retention at elevated temperature. SIMPREX® 1455 have a medium tack and are a great choice for many applications in the range of medium to high service temperature.

Toray E732 is a snap cure toughened epoxy resin matrix optimized for press curing (compression molding) prepreg Applicationss. With a cure time of 4 minutes at 160°C (320°F), an onset Tg of 170°C (338°F) is achieved. At this higher temperature, medium-to-high production rates can be accomplished, with customers able to produce beyond 50,000 parts per year. Toray E732 is a versatile matrix with a range of processing options allowing a variety of automotive and industrial Applicationss to be realized.

Resinoid 1360HR is a glass reinforced, two-step phenolic molding compound. It exhibits outstanding impact strength, electrical and thermal properties. It is particularly suitable for high temperature and strength applications. This material comes in pelletized from and is suitable for transfer or compression molding. It can be preformed on automatic equipment.

I-Speed® laminate and prepreg products are manufactured with Isolas' patentable high performance multi-functional resin system, reinforced with electrical grade (E-glass) glass fabric. This system delivers a 15% improvement in Z-axis expansion and offers 25% more electrical bandwidth (lower loss) than competitive products in this space. These properties coupled with superior moisture resistance at reflow, result in a product that bridges the gap from both a thermal and electrical perspective. The I-Speed® resin system is laser fluorescing and UV blocking for maximum compatibility with Automated Optical Inspection (AOI) systems, optical positioning systems and photo imageable solder mask imaging.

APCM DA 4080 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

Natex P-Preg PP P1/1 900 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

8020 Rapi-Ply is a Outstanding vacuum-bag-only (out-of-autoclave) processing capability. No debulking required off Bi-layer form facilitates fast lay-up

Resinoid Compound 1322 is a glass reinforced, two step molding compound. It may be preformed. Recommended for transfer, injection or compression molding

APCM DA 4518 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 250°F (121°C) for one hour and or a cure of 350º F (177ºC) for 1 hour. This material needs to be post cure or cured to 350ºF to get the 350º properties.

Natex P-Preg PA11 P1/1 900 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polyamide 11 with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.