Products in Building Materials: Epoxy & Epoxy Derivatives

Duresco NU 510-1 F is a Glass fiber reinforced epoxy molding compound with very good mechanical properties for high temperature applications.

A high build, surface-tolerant, semi-gloss epoxy coating formulated for excellent resistance to corrosive and abrasive environments. This product is available in a wide range of attractive colors and is formulated for excellent adhesion to clean steel, rusted steel, weathered galvanized steel, wood, concrete, and most existing cured coatings. This product meets the requirements of ANSI/AWWA D102- 06 OCS-5 for first coat and intermediate coat and OCS-6 intermediate coat. Complies with U. S. EPA Ozone Transport Commission (OTC) for Volatile Organic Compounds for VOC Emission Standards for industrial maintenance coatings.

VF 30™ is a low viscosity, high solids epoxy developed as a penetrating concrete primer for polyurea applications. VF 30 penetrates and strengthens the surface of the concrete, reduces pin-hole formations and provides a chemically reactive surface to accept VersaFlex polyurea systems. Adhesion is increased with the use of VF 30 by up to three times that of unprimed concrete.

SurePoxy Protective Coating WD is a two component, water thinned, VOC compliant, epoxy curing and sealing compound. It provides a protective coating resistant to abrasion, chemicals and has excellent resistance to chloride ion penetration, yet exhibits a high level of moisture vapor transmission when fully cured.

Epovia Optimum® KRF-1051 - novolac epoxy vinyl ester resin, chemical and heat resistance, low color, low foaming, fast cure. Main applications areas are building and construction, chemical industry, industrial sector etc.

OM14 is a fast curing structural prepreg for press curing for the needs of structural parts used in Automotive Industry. Its short curing cycle and hot de-moldable nature are especially optimized for mass production at Automotive Industry with the addition of exceptionally long out life at room temperature. OM14 eliminates the need of Autoclave and Cold storage plus it is especially optimized for mass production. New resin system not only cures under 1-2 minutes at 150°C at press under isothermal curing conditions but also hot de-moldable and long out-life of one year at ambient temperature.

MICAM EM42 is a limited fire hazard laminate which is a glass-fiber reinforced epoxy resin composite material. It is produced by a high temperature and high pressure process which produces a high strength void-free laminate suitable for a range of applications including electrical insulation and building construction applications.

QuakeBond™ 220UR-SC (underwater - slow cure) is a two-component high-strength structural epoxy-resin designed for a variety of applications including underwater marine uses. This adhesive system trowels easily and has a non-sag, high-tack consistency both in ambient and underwater conditions. QuakeBond™ 220UR-SC is a 100% solids formulation with low toxicity and low odor during cure and features a unique pot life of 90-minutes for applications where extended working time is required.

Highland International 70-HF is a high-solids, 2-K High Performance Epoxy Coating formulated for an array of applications including interior liners for vessels, tanks, pipelines carrying mild to medium cargos (process water, fuels, crude oil etc.) up to 212F/100C. 70-HF may also be used for CUI and other exterior services that require exceptional surface tolerance, corrosion protection, and abrasion resistance from ambient up to 250F/121C. This versatile coating will also perform well with dry-heat excursions up to 350F/176C. 70-HF’s engineered viscosity allows for more consistent spray applications regardless of diameter, or equipment: airless, lance, conventional, or specifically engineered. ChemTemp 70-HF Series also offers extended pot life workability and low temperature cure characteristics for easier applications and a quick return to service.

MICOROX® 25-86 PRIMER/SEALER is a two component, 100% solids epoxy resin based product designed as a flexible primer or binder for Decorative Flooring. It is intended for use in areas where thermal or mechanical shock and minor substrate movement is expected. 25-86 will penetrate and seal small cracks and function as a membrane under other flooring systems.

CM12 resin is Mid Tg, dicy-free fast cure, hot demoldable isothermal press curable resin system and it is suitable for sanding and metal composite hybrid part production. Drapability is suitable for press molds and low to medium tack optimized for press curing. Performance of prepreg system with CM12, capable of Class A Surface.

True-Bond PS™ concrete filler and bonder will not separate from concrete. Resurfaces chipped and pitted concrete. Resists wear. corrosives, weather. impact. Bonds cracked curbing, masonry, swimming pools. Waterproof. One application lasts for many years. Can be used at any temperature above 34°F. Quickest cure is at 70° F or higher.

Fielco Adhesives FCO 9502 is a flexible, two-part epoxy adhesive with excellent wetting characteristics for applications requiring metal-metal, metal-plastic, or plastic-plastic bonding.

Rhino Linings USA, Inc. 1310L-6 Resin allows the parts or tools to be used in many elevated service temperature environments. Low mixed viscosity quickly wets thick reinforcements. Convenient 4:1 volumetric mix ratio.

Sumter Coatings Enviro Pox 949 High Build Epoxy is a high build epoxy mastic is a high-quality coating that can be used with or without primer over steel, galvanized metal, aluminum and concrete. Enviro-Pox 949 High Build Epoxy Mastic bonds directly to steel or concrete. A single coat can out perform several coats of alkyd coating. Two coats of this coating may be applie d at one-hour intervals for a total of 15 mils dry film.

Rhino Linings USA, Inc. 3100 Hardener is a Long Pot Life for Civil Engineering.

Cactus Industrial Epoxy Surface And Wet Tolerant Protective Coating is a high-performance solvent-free, two-pack epoxy mastic designed to provide corrosion resistance and abrasion protection in extreme service applications. This specially designed epoxy system is capable of application and curing underwater and form a tough protective barrier. It provides outstanding adhesion on wet blasted surfaces.

SPARTACOTE® Cove Gel is an epoxy system designed for installation as an integral cove base. For use with SPARTACOTE resinous coating systems to create seamless transitions between the floor and wall.

Paceline Nano-Res Resin exhibits higher strength and rigidity than competing epoxy acrylic resins, and provides superior fiber wet out and working characteristics. It is excellent for use with Carbon Fiber, and other new age composite materials such as Kevlar, Spectra, Synthex, Basalt, etc.

TouchStone™ T-2000 Epoxy is a two component, water cleanable, 100% solid epoxy adhesive compound developed for setting of ceramic tile and stone on horizontal or vertical surfaces.

Fielco Adhesives FCO 9501 is a general purpose, flexible, long potlife, two-part epoxy adhesive designed for applications requiring excellent adhesion to metals and plastics.

Cruspec 6000 2K Water Base Epoxy is an extremely durable, easy to apply epoxy. Excellent abrasion, chemical resistance, & low VOC. Brush, roll, or spray.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

Chase Corporation Plasgard 410 Epoxy Coating is a two-part, high-build, solvent-free epoxy coating.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

CHS-EPOXY 574 Is a Bisphenol A/F resin modified by difunctional reactive diluent

OM10 is highly toughened structural Low Tg resin for press and autoclave curing for the needs of structural parts used in Automotive Industry. OM10 prepreg cures at both press and Autoclave with long out-life of 4 weeks at ambient temperature.

Westcoat EC-38 Liquid Dazzle® Epoxy ® is a two-component, 100% solids epoxy made with proprietary metallic additives that create an evolving drift dynamic in this unique epoxy. It is a decorative, glossy, durable, mar and chemical-resistant coating. This highly decorative epoxy comes in many metallic colors.

Ecotechnilin L-FLAXPREG T-UD-50-5m² is a unidirectional (UD) fibers - FLAXPREG T-UD 50.

EPOTUF® 37-140 is the standard, undiluted, general purpose, diglycidyl ether of Bisphenol-A epoxy resin.

Rhino Linings USA, Inc. 1320 Resin is a Ultra Low Viscosity Epoxy Resin. Ultra low viscosity epoxy for infusion. Used for producing composite laminates using injection or vacuum infusion techniques at ambient temperature.

MasterProtect® 100CR is a 100% solids, sprayable, high-build chemical-resistant epoxy coating. It is used to provide resistance to hydrogen sulfide attacks in the water and sewage-treatment industries. It eliminates the need for prefabricated or cast-in-place manhole liners.

AV10AF is a adhesive film prepreg and Adhesive film prepreg for metal-metal, metal-thermoset, thermoset-thermoset, thermoset-honeycomb bonding applications.

CHS-EPOXY 590 Is BPF type.

Uroflex™ 61 is a two component, 100% solid urethane‐modified‐epoxy (UME) hybrid coating and/or lining system specifically designed for utilization in potable, drinking water environments. Uroflex™ 61 is certified by UL to NSF/ANSI Standard 61. Uroflex™ 61 is a high‐build, self‐leveling coating system incorporating a high degree of flexural modulus. Adheres impressively well to concrete, steel, and wood. Uroflex™ 61 is applicator friendly and easy to apply; conveniently produced in a one‐to‐one mix ratio by volume. Uroflex™ 61 is “green” formulated, environmentally friendly, 100% solid (no VOCs, no solvent)‐ certified UL to NSF/ANSI Standard 61.