Products in Composite Materials: Adhesive

Crestafix® 621CC 85 Bonding Paste is a pre-accelerated urethane acrylate/ isophthalic polyester high performance bonding paste. It is a non-sagging, filled compound, specifically designed for the assembly and bonding of GRP moldings. This highliy thixotropic polyester can also be used on timber and plasterboard.

Crestafix® 90-82PA Polyester Bonding Paste is a pre-accelerated polyester bonding paste. This product is a viscous, white, filled compound that is specifically designed for the assembly and bonding of GRP moldings. Its applications include panels, inserts, internal frames, ribs, composite constructions, and car body components. This product is a high productivity grade designed for use with narrow mixers that will dispense at a high flow rate while maintaining thixotropic properties upon vertical application.

Crestafix® 90-78PA Polyester Bonding Paste is a fast-curing, pre-accelerated, orthophthalic polyester bonding paste. It exhibits exceptional handling properties, especially on GRP and wood substrates. This product has been specifically designed for the assembly and bonding of GRP moldings such as panels, inserts, internal frames, ribs, and any other non-structural bonding applications. It is non-sagging and does not require resin additions.

Crestafix® F26R Polyester Compound is a water-resistant, low-density, polyester-based fairing compound. This product has good adhesion to cured fiber-reinforced polyester and vinyl ester laminates. It sands easily and gives a hard finish after a full cure, yet is not brittle and has good impact strength.

Crestafix® 621CC 45 Bonding Paste is a pre-accelerated urethane acrylate/ isophthalic polyester high performance bonding paste. It is a non-sagging, filled compound, specifically designed for the assembly and bonding of GRP moldings. This highly thixotropic polyester can also be used on timber and plasterboard.

Crestafix® 90-80PA Polyester Bonding Paste is a pre-accelerated, orthophthalic polyester bonding paste that is reinforced with 3 mm glass fibers. This product exhibits exceptional mechanical and handling properties, has low shrinkage, and has better resistance to impact. It has been specifically designed for the assembly and bonding of GRP moldings such as panels, inserts, internal frames, ribs, composite constructions, and car body components. It is non-sagging and does not require resin additions.

Crestafix® 630PA is a pre-accelerated vinyl ester-based high-performance bonding paste. This product is a non-sagging, filled compound with high strength, specifically designed for the assembly and bonding of GRP moldings. Its applications include panels, inserts, internal frames, ribs, internal core materials, and composite constructions. This product provides high shear strength bonded joints without the need for mechanical fixings.

Crestafix® B72R Bonding Paste is a polyester-based, MEKP catalysed core bedding compound, developed for both hand-layup and vacuum-bag core installation. It is used as a 2-part system in conjunction with a priming resin applied to the core surface. Lightweight and non-sagging, Crestafix® B72R is formulated to the degree of elasticity required for the core to skin interface.

Crestafix® B39 Adhesive is a high strength pumpable polyester adhesive formulated for production environment in boatbuilding and general fiberglass fabrication. It was formulated to provide reliable structural bonds in both thin and thick bondlines (1/8” to 1”, 3 - 25mm). The product has low shrinkage, low exotherm and no volume loss during pumping.

Crestafix® 90-84PA Polyester Bonding Paste is a lightweight, low-exotherm, pre-accelerated orthophthalic polyester bonding paste. It is a non-sagging compound, designed for non-structural applications where gap-filling may be a secondary requirement. This product has been specifically designed to provide weight-saving properties and ease of application.

StrongBond™ 200 Adhesive Putty System is a high-strength, toughened, structural epoxy adhesive for the bonding of carbon fabrics to itself and many dissimilar materials. It is a two-phase (toughened) epoxy resin produced using a CTBN elastomer with a flexible epoxy resin backbone for maximum stress and fatigue resistance. StrongBond™ 200 Adhesive Putty System with an immediate high tack consistency, a long working life, and a quick cure time. StrongBond™ 200 Adhesive Putty System may be used at ambient temperature(s) ranging from 55°F(13°C) to 100°F (38°C). The working life at 100°F (38°C) is > 2 hours (working time increases with lower ambient temperatures), with full cures occurring between 6-12 hours depending on cure temperature. Unlike most epoxy adhesives, StrongBond™ 200 Adhesive Putty System cured at ambient temperatures provides heat resistance well more than most engineering limits with an HDT of 85°C (185 °F). The material mixes at 2:1 by volume or 100:44 by weight (resin to hardener). The convenient color-coded components form a uniform color when properly mixed. StrongBond™ 200 Adhesive Putty System is designed for high production meter/mix ram dispensing and although highly thixotropic, has very fast application rates. With low odor and toxicity, StrongBond™ 200 Adhesive Putty System is solvent-free, and 100% solids.

Fiberglass (A/Asia) Sales Pty Epoxy 6000 is a high strength, high impact resistant adhesive epoxy gel. The mixed product is a clear amber with both excellent spreading and non-sagging capacity.

RECKLI Adhesive Paste EP is a slightly thixotropic, solvent-free, two-component adhesive resin for the adhesion of wood, paperboard, natural or synthetic stone, various metals and plastics. Its color is creamy-white.

MTFA400 resin film is designed to give enhanced toughness and higher service temperature, giving great flexibility in component manufacture. It is a toughened epoxy resin system that can be supplied with or without fabric support to meet your cost and manufacturing requirements.

P & P Technology AS-SCS001 CONDUCTIVE SILICONE CAULK is an electrically conductive composite material comprising of silicone elastomer and silver plated copper particles. It is designed to be easily applied to panel joints &seams and/or the small clearances that result from non-continuous mechanical fixing in sheet metal enclosures. On application it cures at room temperature to form a highly conductive elastomeric section / joint that has good adhesion to most commonly used metals &substrates. When fully cured it will prevent water ingress and improve the EMI shielding performance of panel joints &overlaps.

Guangzhou Lushan New Materials EP252 is maleic grafted polyethylene. It’s mainly used for reinforced PE spiral corrugated steel pipes and steel wire with large caliber. Adhesive resin Lushan EP252 solves the adherence problems between plastics and plastics, plastics and metal, glass and other materials.

Guangzhou Lushan New Materials EF-3 is adhesive resin Lushan series for multi-layer barrier food packaging film has durable bonding properties when adheres to Polarity materials, such as PE, PP and PA, EVOH, etc.

HiMax™ 3gsm DPA (Dot Pattern Adhesive) products are designed to help composite manufacturers maintain the desired position of the reinforcement prior to resin introduction, particularly in closed mold processes such as vacuum infusion and resin transfer molding. HiMax™ DPA was developed to provide the optimal level of tack while keeping additional weight to a minimum. The novel application process allows just 3 grams per m2 of adhesive to be applied to the specified fabric. Using DPA in conjunction with HiMax™ fabrics allows the user to easily position and re-position the individual layers of their laminate stack before resin is introduced. Conformance to tight radii and complex mold geometry is also aided by DPA.

Guangzhou Lushan New Materials M-1 is Adhesive resin Lushan series for barrier container and tube is used for bonding a wide variety of materials. It's most often used to adhering PE and EVOH, PP and EVOH, etc.

Guangzhou Lushan New Materials M-8D is Adhesive resin Lushan series for multi-layer barrier food packaging film has durable bonding properties when adheres to Polarity materials, such as PE, PP and PA, EVOH, etc. Adhesive resin Lushan series is used as tie layer resin and widely used for application of food packaging such as fruit oil, milk, water, juice& meat bags, etc.

KarpatSmoly UMF Resin Grade B is an aqueous suspension, non-flammable, non-explosive. The finished product contains 10% of melamine by weight.

KarpatSmoly MUF Resin is an aqueous suspension, non-flammable, non-explosive. The finished product contains 10% – 24%of melamine by weight.

HiMax™ 8gsm DPA (Dot Pattern Adhesive) products are designed to help composite manufacturers maintain the desired position of the reinforcement prior to resin introduction, particularly in closed mold processes such as vacuum infusion and resin transfer molding. HiMax™ DPA was developed to provide the optimal level of tack while keeping additional weight to a minimum. Using DPA in conjunction with HiMax™ fabrics allows the user to easily position and re-position the individual layers of their laminate stack before resin is introduced. Conformance to tight radii and complex mold geometry is also aided by DPA.

MTFA500 (DF044) toughened epoxy adhesive film is design to cure between 80°C and 120°C, allowing flexibility in component manufacture.

KarpatSmoly UMF Resin Grade A is an aqueous suspension, non-flammable, non-explosive. The finished product contains 10% of melamine by weight.

Guangzhou Lushan New Materials EP253H is a Adhesive resin Lushan series for aluminum-plastic composite pipe is maleic grafted polyethylene used for PE-AL- PE, PEX-AL- PEX and PERT-AL- PERT composite pipes. Lushan adesive resin could provides innovative solutions for plumbing and heating pipe systems including applications of domestic water piping, under-floor heating, radiator connections and wall, cooling and heating installations, district heating and industrial piping, etc.

Guangzhou Lushan New Materials M-12A is Adhesive resin Lushan series for multi-layer oxygen barrier pipe is a modified polyolefin with functional groups. It's designed to bond to a variety of barrier materials, such as nylon and ethylene vinyl alcohol (EVOH), etc.

VTFA400 (DF034) toughened epoxy adhesive film is design to cure between 65°C and 120°C, allowing flexibility in component manufacture.

Guangzhou Lushan New Materials PF-3 is Adhesive resin Lushan series for multi-layer barrier food packaging film has durable bonding properties when adheres to Polarity materials, such as PE, PP and PA, EVOH, etc. Adhesive resin Lushan series is used as tie layer resin and widely used for application of food packaging such as fruit oil, milk, water, juice& meat bags, etc.

Guangzhou Lushan New Materials M-10A is Adhesive resin Lushan series for sausages casing film is anhydride-modified polyethylene product and is available in pellet form.