Products in Other Devices & Assemblies: High Stiffness

Idemitsu Chemicals Xarec® S135 is a Syndiotactic Polystyrene (SPS) product filled with 30% glass fiber. It can be processed by injection molding and is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America. Primary characteristic: flame rated.

GEHR PBT® is a semi-crystalline material from the polyester family of plastics and, due to its good thermal and mechanical properties, is counted among the polymer group of engineering plastics. It has a high surface hardness and good sliding and wear behavior.

Grupa Azoty S.A Tarnoform® 300 GF2 GB2 there is 10% glass fibers & 10% glass beads reinforced injection- molding grade with increased strength and stiffness and with reduced warpage tendency.

Grupa Azoty S.A Tarnoform® 500 GF8 is a 30% glass fibers reinforced injection-molding easy flowing grade with extremly high strength and stiffness and reduced shrinkage and coefficient of linear thermal expansion.

GEHR PA® 6 C is a high-molecular and stress-reduced PA 6, which shows a very tough behavior and which was produced by casting. Our round rods and sheets in natural color comply with the food contact regulations according to 10/2011/EC.

Nylene 33% glass fiber reinforced heat stabilized nylon 6 injection molding resin. High heat and chemical resistance inherent in nylon type resins, along with higher strength and stiffness due to glass fiber reinforcement. Excellent surface appearance when processed in a warm mold. Suitable for brackets, levers, handles, enclosures, and other applications where high physical properties combined with good appearance are required. The ASTM line call out for this product is D4066 PA022G33

Nilit NILAMID® B2 HH GF60 is a Polyamide 6 (Nylon 6) compound, 60% glass fiber reinforced, high heat stabilized.This high stiffness and glossy finish compound is intended for injection molding.NILAMID® B2 HH GF60 is primarily designed for the Automotive industry. It is also suitable for Electrical and Electronic or Industrial & Consumer applications.

Nemcon™ E-series products are designed for use in ESDA electronic assembly environments where strict control of ESD and cleanliness are critical. Nemcon™ E PC 08CF is a carbon fiber reinforced polycarbonate characterized by high stiffness, consistent moldability, low sloughing and uniform conductivity.

fluteck™ K304 PEEK is a high performance thermoplastics polymers based on unreinforced Polyetheretherketone (PEEK).

Manifattura Cattaneo PET is a Crystalline thermoplastic suitable for the production of high precision parts to which good lubrication is added.

Badamid® LA70 GF30 by Bada AG is comprised of Polyamide 66. It is commonly used It is available in Granules form.

The natural cast polyamide reveals characteristics that are very close to the same ones found in Manifattura Cattaneo PA 6 G. It combines high mechanical resistance, rigidity and hardness with good resistance to wear and creep, as well as a good resistance to thermal aging and good machinability on machine tools.

fluteck™ K308 PEEK is a high performance thermoplastics polymers based on unreinforced Polyetheretherketone (PEEK).

MECHATEC ACETAL is a Polyoxymethylene Copolymer ( POM-C ) which has excellent machining stability, high strength and stiffness, superior wear resistance, large size capability.

Since its introduction in 1938, Nylon has become one of the world’s most widely recognized and utilized engineering grade thermoplastics. Nylon’s unique combination of high strength, good toughness, outstanding chemical resistance, and excellent wear and abrasion resistance have made it the material of choice for product designs in a multitude of industries. When used to replace wear grade metals like brass and bronze, no other material provides the combination of extended wear life, light weight, and low fabricated part cost of Nylon. Polymer Industries manufactures MECHETEC® Nylon stock shapes in a wide variety of types and stock shape configurations including glass filled and molybdenum disulfide (MoS2 or moly) filled options. Formally known as Unipa Nylon. For more Info : Click Here

Compared to virgin Manifattura Cattaneo PA 6.6 30% GF glass fiber reinforced polyamide exhibits improved mechanical strength, stiffness, dimensional stability and creep resistance, as well as excellent wear resistance retention and the ability to use at higher temperatures .

Tarnoform® 300 GF4 TF3 is a polyacetal copolymer (pom) polymer lowered wear and friction coefficient modified with 20% glass fibers reinforced.

Glass reinforced (20 %) Polyether Sulfone. Excellent chemical and electrical resistance, high stiffness, modulus and HDT.

ProPolymers PPA TI-35G is a 35% glass fiber reinforced hest stabilized polyphthalamide (PPA) resin. It has very high stiffness, tensile strength, and heat deflections temperature combined with low water absorption and creep.

Nylene 33% glass fiber reinforced PA 6,6/6 injection molding grade High strength and stiffness of reinforced nylon,lower crystallinity associated with nylon 6,6/6 Suitable for handles and levers, housings, brackets, and other similar uses. NC-101 would indicate Natural color UV for UV protection and UW for Weatherability.

Grupa Azoty S.A Tarnoform® 300 SI is an Acetal (POM) Copolymer material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding.Important attributes of Tarnoform® 300 SI are: Flame Rated Chemical Resistant Bacteria Resistant Copolymer Fatigue Resistant Typical applications include: Engineering/Industrial Parts Automotive Plumbing/Piping/Potable Water

GEHR PA® 6 XT is a PA 6 which shows a very tough behavior and which was produced by extrusion. Our round rods and sheets in natural color comply with the food contact regulations according to 10/2011/EC.

Thermally Conductive Polyetheretherketone, excellent chemical, high stiffness, modulus and HDT.

GEHR POM® C is produced from the continuous operating temperature of this engineering plastic ranges between -40 °C and +100 °C. Based on its toughness combined with high dimensional stability, there is no tendency to stress cracking. The copolymer has high thermal stability and chemical resistance. In particular, the increased hydrolytic stability and resistance to contact with many solvents must be taken into account. This material is frequently found in applications in the food industry, as cleaning processes require resistance to the use of hot water or various chemical agents. Our round rods and sheets in natural or black color comply with the food contact regulations according to 10/2011/EC.

Polypropylen +40% Talcum abbreviated as PP+Talcum40.

Trilene BI32AN is a nucleated Impact Copolymer Polypropylene (ICP) for electronic appliances, automotive and general purpose applications requiring high flow and impact strength. This grade is nucleated to provide lower warpage, greater modulus, and faster cycle time.This grade uses Unipol® polypropylene technology with latest catalyst technology.

Nylene 43% glass fiber reinforced, heat stabilized, nylon 6 injection molding resin Heat and chemical resistance typical of nylon 6 resins, while glass fiber reinforcement provides outstanding strength and stiffness The nylon 6 base resin also provides excellent surface appearance Suitable for brackets, supports, enclosures, handles, and any other uses which require high stiffness along with good appearance

Grupa Azoty S.A Tarnoform® 300 GF4 is a 20% glass fibers reinforced injection-molding grade with high strength and stiffness and reduced shrinkage and coefficient of linear thermal expansion.

INNOPOL® CS 2-4630 FR is a halogen-free flame retarded polypropylene block-copolymer compound. This grade is available in nature and custom colored form.

MECHETEC® Delrin® (polyoxy-methylene) offers design engineers a superior blend of strength, stiffness, lubricity, and dimensional stability. These properties, along with inherent machining ease, have made MECHETEC® Delrin® one of the most widely used engineering grade thermoplastics. To meet specific application configurations and to maximize production efficiencies, Polymer Industries offers a broad array of MECHETEC® Delrin® stock shapes. These materials include both homopolymer unfilled grades as well as PTFE-filled grades for enhanced wear resistance and DE-588 options for military applications. Formally known as Unital Delrin. For more Info : Click Here

fluteck™ K303 PEEK is a high performance thermoplastics polymers based on unreinforced Polyetheretherketone (PEEK).

Grade with 20% glass beads, high rigidity and hardness with reduced warping. ISO 9988-1: POM-K, M-GNR, 03-003, GB20

INNOPOL® CS 2-4120 is a 20% talc filled compound based on a polypropylene block-copolymer. This grade is available in nature and custom colored form.

GEHR PC® is a transparent material and belongs to the group of amorphous engineering plastics as well as to the polyester family of plastics. It has a high stiffness and extremely high impact strength. It also has a high glass transition temperature and heat deflection temperature (approx. +130 °C). The continuous operating temperature of PC ranges between approximately -60 °C and +120 °C. The material is highly resistant to high-energy radiation. However, it must be stabilized against UV rays, otherwise yellowing may occur. Like all polyesters, PC is not resistant to hot water (from approx. +60 °C) in the long term.

Grade with 30% glass beads, very high rigidity and hardness with reduced warping. ISO 9988-1: POM-K, M-GNR, 03-003, GB30

GEHR PA® 6.6 is slightly increased surface hardness and rigidity of PA 6.6 is due to the reduced moisture absorption behavior compared to PA 6 XT. Abrasion resistance and heat deflection temperature could also be optimized at the expense of toughness.