Products in Pools & Landscaping

Madewell® 1312S™ is a heavy duty, 100% solids, two component epoxy coating product. It is used for both new construction and maintenance of steel and concrete surfaces in pools, tanks, sumps, trenches, decks, and pipe interiors. Madewell® 1312S may be used as a topcoat over other Madewell® coating systems to add color and/ or seal the surface. M Madewell® 1312S protects surfaces against chemical attack under immersion, spill, and splash conditions, and impact and abrasion damage caused by rough use or heavy traffic. It is normally applied at a nominal thickness of 10 to 20 mils in two coats. Its monolithic construction resists moisture, chemical, and bacteria penetration while also being attractive and easy to clean. Its free spreading characteristics, fast set time, and ease of cleanup help to minimize labor costs and down time.

Soric® XF 4 is the cost effective solution for closed mold processes. It is used as core material and infusion medium. It is a pressure stable polyester nonwoven and compatible with all regular types of resins, including Polyester, Vinylester, Phenolic and Epoxy. It is suitable for closed mold processes, including Infusion, RTM Light, RTM Heavy.

Admix C-1000 RED is added to the concrete mix at the time of batching. Admix C-1000 RED consists of Portland cement, very fine silica sand, a red oxide pigment and various active, proprietary chemicals. These active chemicals react with the moisture in fresh concrete and with the by-products of cement hydration to cause a catalytic reaction which generates a non-soluble crystalline formation throughout the pores and capillary tracts of the concrete. Thus the concrete becomes permanently sealed against the penetration of water or liquids from any direction. The concrete is also protected from deterioration due to harsh environmental conditions.

AS 10 is an antistatic additive with PE Resin.

WALL-GLAZE is a non-yellowing water-based interior masonry sealer formulated to provide a protective coating for concrete and masonry surfaces. It is available in clear and a wide range of colors in a gloss, semi-gloss and low sheen finish. WALL-GLAZE is recommended for all exposed concrete and masonry.

Classic satin medium gloss is a clear single component acrylic sealer that is designed to be used over all of our stains, polymer-modified cement toppings, waterborne colorants, masonry, concrete, pavers, natural stone and brick. Classic satin medium gloss sealer is a waterborne acrylic with low VOC, no fumes, low odors and high solids. May be used for interior or exterior applications in a wide range of climates.

PPA 30D is a polymer processing aid with PE Resin.

MiraGard Colorbond SR is a single component, self-crosslinking, and solar-reflective pigmented acrylic coating designed for application on concrete plaza decks, balconies, roof deck surfaces, and as a topcoat for polymer modified cementitious coatings such as Miracote MPC. An important characteristic of MiraGard Colorbond SR is that it increases the solar reflectance index (SRI) of the exposed surface, which results in a significantly cooler surface. It also features excellent hiding attributes, wash-down characteristics and provides excellent weathering and wear resistance. MiraGard Colorbond SR Topcoat is an easy to apply economical coating. It is recommended for resealing some Miracote systems to improve overall energy savings, via reduction in conditioned air utility costs. It may be applied to properly prepared surfaces where stain resistance and cleanability are a consideration.

Polipol 3401 is a Hand lay-up / Spray-up polyster.

Coremat® Xi 4 is the cost effective solution for open mold processes, It is used as core material and/or print blocker It is a polyester nonwoven and compatible with all regular types of resins, including Polyester, Vinylester, Phenolic and Epoxy. It Is suitable for hand lay-up and spray-up process

Polipol 3401-TA-H20 is a Hand lay-up / Spray-up thixotropic preaccelarated polyster.

SIMONA® PE 100 black 10024798 Line range of pipes and fittings with FM certification offers a superior standard of safety and quality for use in subterranean fire extinguishing systems. What is more, SIMONA® is the first plastics manufacturer worldwide to supply "FM APPROVED" pipes and fittings in sizes up to d 630 mm. It has High heat stability, UV-stabilized, creep strength at 50 years, 20°C, medium water = 10 Mpa.

Micro-FL-1014 5B is an economical masterbatch based on Talc with LDPE carrier which contributes to extrusion process stability and improved output. It improves MD tear resistance and dart impact properties , retains light transmission levels and improves MD/TD shrinkage levels.

Densetec® Marine Board is specially formulated to withstand the rigors of harsh outdoor marine environments. It is UV-stabilized to resist damage and retain its beauty, even after years of direct sunlight. Increasingly, Densetec® Marine Board is replacing wood and laminates in boating applications. It does not splinter,crack, delaminate, rot, swell, or absorb water like traditional materials. Even under heavy foot traffic on yacht decks, it remains virtually maintenance-free. In addition, there is no need to stain or paint Densetec® Marine Board every few years. The color is integrated with the polymer and retains its vibrant appearance better than painted wood. Fabricating and finishing are easy with standard woodworking tools. Densetec® Marine Board forms easily for smooth curves and bends. Since there is no grain pattern, parts can be cut from any part of the sheet virtually eliminating waste for greater economy than wood. Densetec® Marine Board is also available in two other formulations for specific applications: Densetec® Marine HP (High Performance) and Densetec® Marine LW (Lightweight).

Lavecoat IO is based on IsoPhtalic resin, provide very protection and good mechanical performance in external applications with exposure to water and sunlight.

Alabama Pigments Company Terra Cotta Class I is a color hardener which are a pigmented cementitious powder that can be broadcast or dusted onto the surface of freshly placed concrete, to create a dense, abrasion-resistant surface that is permanently colored. Color hardeners can be troweled, broom finished or textured and stamped to create authentic looking stone or patterned textures. The use of color hardeners make it possible to achieve any number of bright or light colors, or any combination of them on gray concrete.

Alabama Pigments Company Adobe Buff Class Ii is a color hardener which are a pigmented cementitious powder that can be broadcast or dusted onto the surface of freshly placed concrete, to create a dense, abrasion-resistant surface that is permanently colored. Color hardeners can be troweled, broom finished or textured and stamped to create authentic looking stone or patterned textures. The use of color hardeners make it possible to achieve any number of bright or light colors, or any combination of them on gray concrete.

Polipol 3401-TA-H40 is a Hand lay-up / Spray-up thixotropic preaccelarated polyster.

Polipol 3401-A is a Hand lay-up / Spray-up preaccelarated polyster.

SIMONA® PE 100 black 10024792 Line range of pipes and fittings with FM certification offers a superior standard of safety and quality for use in subterranean fire extinguishing systems. What is more, SIMONA® is the first plastics manufacturer worldwide to supply "FM APPROVED" pipes and fittings in sizes up to d 630 mm. It has High heat stability, UV-stabilized, creep strength at 50 years, 20°C, medium water = 10 Mpa.

SIMONA® PE 100 black 10024789 Line range of pipes and fittings with FM certification offers a superior standard of safety and quality for use in subterranean fire extinguishing systems. What is more, SIMONA® is the first plastics manufacturer worldwide to supply "FM APPROVED" pipes and fittings in sizes up to d 630 mm. It has High heat stability, UV-stabilized, creep strength at 50 years, 20°C, medium water = 10 Mpa.

Polipol 339-TA-LSE-H20 is a Hand lay-up / Spray-up thixotropic preaccelarated LSE polyster.

Polipol 3401-TA-LSE-H40 is a Hand lay-up / Spray-up thixotropic preaccelarated LSE polyster.

Polipol 3401-TA-LSE-H20-White is a Hand lay-up / Spray-up thixotropic preaccelarated LSE white polyster.

SIMONA® PE 100 black 10024791 Line range of pipes and fittings with FM certification offers a superior standard of safety and quality for use in subterranean fire extinguishing systems. What is more, SIMONA® is the first plastics manufacturer worldwide to supply "FM APPROVED" pipes and fittings in sizes up to d 630 mm. It has High heat stability, UV-stabilized, creep strength at 50 years, 20°C, medium water = 10 Mpa.

ZOLTEK PX35 Stitch-Bonded Uni-Directional Carbon Fabrics are produced from our ZOLTEK PX35 50K Continuous Tow Carbon Fiber. Unique fiber spreading techniques are utilized to obtain a wide range of UD fabric weights for a varied set of composite part applications. Quick composite part build-up is cost effectively achieved with our diverse weight range of low-cost carbon fabric products.

ZOLTEK PX35 Stitch-Bonded Uni-Directional Carbon Fabrics are produced from our ZOLTEK PX35 50K Continuous Tow Carbon Fiber. Unique fiber spreading techniques are utilized to obtain a wide range of UD fabric weights for a varied set of composite part applications. Quick composite part build-up is cost effectively achieved with our diverse weight range of low-cost carbon fabric products.

ZOLTEK PX35 Stitch-Bonded Uni-Directional Carbon Fabrics are produced from our ZOLTEK PX35 50K Continuous Tow Carbon Fiber. Unique fiber spreading techniques are utilized to obtain a wide range of UD fabric weights for a varied set of composite part applications. Quick composite part build-up is cost effectively achieved with our diverse weight range of low-cost carbon fabric products.

ZOLTEK PX35 Stitch-Bonded Uni-Directional Carbon Fabrics are produced from our ZOLTEK PX35 50K Continuous Tow Carbon Fiber. Unique fiber spreading techniques are utilized to obtain a wide range of UD fabric weights for a varied set of composite part applications. Quick composite part build-up is cost effectively achieved with our diverse weight range of low-cost carbon fabric products.

ZOLTEK PX35 Stitch-Bonded Uni-Directional Carbon Fabrics are produced from our ZOLTEK PX35 50K Continuous Tow Carbon Fiber. Unique fiber spreading techniques are utilized to obtain a wide range of UD fabric weights for a varied set of composite part applications. Quick composite part build-up is cost effectively achieved with our diverse weight range of low-cost carbon fabric products.