Products in Thermoset Elastomers: Ethylene Propylene Diene Terpolyme...

DLR Elastomer Engineering Ltd EN 45545-2 is a black fire resistant Ethylene Propylene Diene Rubber (EPDM).EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

PEXIDAN® SX554 pre-grafted base is mixed with a crosslinking catalyst masterbatch CM493, in the ratio 95:5, or CM497, in the ratio between 90:10 and 93:7.CM493 is a stronger catalyst suitable for wall thicknesses > 1.5mm and CM497 is a weaker catalyst suitable for small conductor sizes, such as 1 to 4 mm2. The system SX554:CM493 or SX554:CM497, has been approved for use at 1kV and has found uses up to 10kV, it is highly flexible and enables the production of soft rubber cables without the use of continuous vulcanization equipment. Crosslinking is obtained by exposure to moist or hot water immersion only.

EPDM 80 B WRAS R1 [E6392] is an EPDM elastomer with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 70.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

EPDM Peroxide 80 WRAS G is a Peroxide Cured EPDM elastomer, with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 80.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

PEXIDAN® SX505NT pre-grafted base is mixed with a crosslinking catalyst masterbatch CM493 or CM497, in the ratio 95:5. The SX505NT:CM493 or SX505NT:CM497 systems have passed type-tests for use up to and including 36 kV. The graft compound contains a non-staining stabilizer and an effective tree retarder, giving outstanding long term retention of dielectric strength. This compound is typically used in conjunction with crosslinkable semi-conducting material for conductor and insulation shields. Crosslinking is obtained by exposure to moist or hot water immersion only.

EPDM 70 B WRAS R1 [E6029] is an EPDM elastomer with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 70.

A High Ethylene Polymer with Good Green Strength for Wire and Cable and Extruded Profiles

Seals Eastern Compound 7240 is 52-duro EPDM.

J. Allcock & Sons EPDM Granules is produced by the ambient grinding of EPDM waste / scrap material. EPDM is a rubber made from either a co-polymer of ethylene and propylene – which will be peroxide cured, or a ter-polymer which has a small amount of an unsaturated polymer added – this will be sulfur cured. The two different types are rigorously segregated, both as scrap and as finished crumb (or granules).

D10060 is EPDM based compound that is medium hard with dimension stability.

Goodyear Rubber Company of So. California EPDM polymer (Ethylene Propylene Diene Monomer rubber) is a type of synthetic elastomer characterized by wide range applications. Main properties of EPDM are its outstanding heat, ozone and weather resistance. EPDM exhibits satisfactory compatibility with hydraulic fluids, ketones, hot and cold water and alkalis.

Detectaseal® XN7A is the latest advance in contamination detection and containment. This unique range of metal detectable elastomer compounds has been developed specifically to meet the stringent demands of the pharmaceutical and food processing industries.The Detectaseal® fragments as small as 2-3mm can be easily identified by in-line metal detection equipment used to detect product contaminated by process lines.The Detectaseal® range includes Nitrile, Silicone, EPDM and Fluoropolymer (FKM) elastomer compounds (all FDA-compliant) available in blue and black, which allows the most appropriate material to be selected for every application.Detectaseal® compounds can be molded into O-rings and custom components.Key Attributes Early detection and containment of contamination: Reduced product loss, Increased productivity Blue seals to assist in easy identification Excellent mechanical properties and sealing efficiency Exceptional oil and heat resistance FDA-compliant elastomer materials Free from animal-derived ingredients Typical Applications Static and dynamic sealing applications Food processing equipment Pharmaceutical drug manufacturing equipment Bioscience industry.

Blue, Ethylene Propylene Terpolymer (EPT), 65-75 IRHD. Terpolymer of ethylene, propylene and diene monomers. Formulated using only those ingredients determined by the United States Food and Drug Administration (FDA), in accordance with Code of Federal Regulations Title 21 (CFR21), Section 177.2600. ASTM & ISO designation = EPDM.Formulated for repeated use with aqueous foodstuffs intended for human consumption. Not suitable for use with fatty foodstuffs

A High Ethylene, Low Viscosity Polymer with High Green Strength for Wire and Cable Applications

ETHYLENE PROPYLENE RUBBER (EPR/EPDM) 505A is an amorphous rubber with low molecular weight and high ENB content, 505A is able to be applied for various types of product by taking advantage of its good flow and high cure rate, By blending with diene type rubbers such as a natural rubber, 505A plays significant roles to improve their ozone resistance, 505A is also suitable for foam applications made by continuous curing and it produces various sponge products with low density.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK7534 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

A General Purpose Sponge and Tire Polymer

An Ultra Fast Curing Polymer for Automotive Extrusions

General Purpose, Ethylene Propylene Terpolymer (EPT) 75-85 IRHD. Terpolymer of ethylene, propylene and diene monomers. To meet Aerospace specification DTD 5597A Grade 80. ASTM & ISO designation = EPDM.For sealing applications where good fluid resistance and low compression set are of prime importance. For continuous and/or intermittent use in contact with phosphate ester or silicone hydraulic fluids within the temperature ranges as quoted. Suitable for applications in contact with air, this material has excellent resistance to ozone. Unsuitable for use in contact with fuels, mineral oil based and diester oils and silicate fluids or greases derived from these.

An Ultra Fast Curing Polymer for Automotive Extrusions

Unirubber Black EPDM Recycled Granules is a scrap based on EPDM rubber.

KEP® 070P produced by Kumho Polychem is a highly functional special synthetic rubber that is mainly used for automotive parts and has excellent resistance to heat, ozone, and chemicals. With a lower specific gravity compared with other synthetic rubbers, it can be applicable for high-filling mixing, meaning it has a high economic feasibility.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5813 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

JSR EP96 is high filler loadingoil extended EPDM.

D10070 is EPDM based compound that is medium hard with dimension stability.

G&E 254 is produced from feedstocks carefully selected for uniform viscosity, ethylene propylene ratio, and 3rd monomer. The feedstocks are chosen to produce a blended EPDM Polymer which has a medium ethylene content, medium diene content, and low mooney. G&E Blended EPDM 254 can be blended with prime EPDM polymers to reduce compound costs in extruded, calendered and molded applications.

Climarub 1.3 is developed to reduce the environmental impact. It can replace traditional EPDM rubber resulting in considerably lower CO₂ emission. Technically, Climarub performs just as well as traditional EPDM rubber.

Climarub 0.7 is our new rubber material developed to reduce the environmental impact. It can replace traditional EPDM rubber resulting in considerably lower CO₂ emission. Technically, Climarub performs just as well as traditional EPDM rubber.

Polymer-Technik Elbe EPDM - Sulfur TWK8684 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

E80Q is a peroxide-cured, Ethylene Propylene Terpolymer material formulated using only those ingredients determined by the US Food and Drug Administration (FDA). E80Q is suitable for use in food contact applications requiring FDA and 3A compliance.E80Q provides excellent water and steam resistance and good compression set properties. The material's heat and chemical resistance is superior to that of sulfur-cured EPDM.Available in any sized O-ring (fully molded up to 2.5m/8ft internal diameter), gaskets and custom designed components.Key Attributes FDA compliant to CFR 21 § 177.2600 (a-d) 3A Sanitary Standard 18-03 Class 2 compliant Free from Animal Derived Ingredients (ADI) Typical AttributesRecommended for use in food and dairy applications. O-rings Gaskets Hygienic/sanitary couplings & pipe connectors Valves Pumps Metering equipment

An Excellent Polymer for Hose and Extruded ProfilesUnique Features Fast Curing Excellent extrusion properties: low die swell, high extrusion rate High green strength, excellent shape stability Friable bale provides excellent dispersion Highly extendable Good low temperature properties Applications Extruded Profiles Hose Molded Products

Seals Eastern Compound 7075 is 68-duro EPDM.

Seals Eastern Compound 7189 is 53-duro EPDM.

D10050 is EPDM based compound that is medium hard with dimension stability.

A General Purpose Extrusion and Molding Polymer

POLIGOM is available in a wide range of SHORE HARDNESS with feature of flame retardant thermoplastic, halogen-free and exceptional flexibility. The product is available with high level of tensile strength, excellent levels of tear strength and free plasticizers (XEPR/XHEPR), and is also characterized by a particularly low value of Specific Gravity.