Products in Automotive & Transportation: Epoxy & Epoxy Derivatives

BONDiT™ B-482 is a two-part, state-of-the-art 100% solids, room-temperature curing flexible epoxy resin system. Especially designed for potting, coating, and adhesive applications for electronics and electrical assemblies, environmental sealing, hard coating for corrosion resistance, bonding engineering plastics and elastomers to various substrates.

Kukdo Chemical KD-3013 Epoxy Resins are bisphenol-A type half-capped epoxy resin, and designed for applications of high performance powder coating, especially FBE(Fusion Bonded Epoxy coating). The most advantage of these products is that residual bisphenol-A content is the less than one percent by weight. Also, these products have excellent performance of block resistance, chemical resistance and mechanical properties.

Attshield 47 is a novolac epoxy vinyl ester resin that resists corrosion in a wide range of solvent, acidic, and slightly alkaline environments. This tough, high-strength resin is used to make fiberglass-reinforced laminates with high impact strength and resistance to a variety of mechanical stresses. This resin is ideal for filament winding and the production of products that require resistance to harsh environments and temperature changes. This resin has excellent wettability and curing properties as well.

Polyglass Coatings Caliber Low VOC Primer is a high solid, low VOC, epoxy zinc primer. It provides superior adhesion, cathodic corrosion protection and impact resistance.

ACP Composites Carbon Fiber High Gloss Woven Sheets are an outstanding decorative laminate with a deep, glossy, three dimensional finish. Our proprietary Autoclave curing process produces the most consistent and highest quality gloss carbon fiber sheets possible. Manufactured using 100% real carbon fiber fabric pre-impregnated with high quality epoxy resin, these sheets are cured at high temperatures and pressure to ensure a strong, rigid product that cannot be re-shaped after cured. Unlike a wet layup, our Autoclave curing process consistently yields flat, lightweight sheets with minimal voids, waves or buildups.

ACP Composites 8.8 oz Fiberglass 8-Harness Satin Weave RTS Prepreg is a Satin Weave EGlass fabric impregnated with a thermosetting epoxy resin system. . It is storable at room temperatures and does not require freezer storage. With the long out life of the resin matrix, the carbon fiber prepreg can be shipped and handled at room temperatures. It is ideal for use when a long shelf life is desired, high-temperature capabilities are not required and controlled resin content is wanted.

Niskoat FerraPrime Epoxy Primer is a two-component, premium quality epoxy primer, ideal for ferrous applications requiring corrosion and chemical resistance, and mechanical durability. It is excellent for use on heavy equipment, exterior storage tanks, trucks and trailers, farm implements, and oilfield equipment.

AX-6201XL is a Structural Epoxy Unidirectional Prepreg for Vacuum Bag Only Processing.

AX-5270 is a Structural Epoxy Carbon Prepreg.

Razeen® SL 4072X75 is a typical type 2 epoxy resin based on Bisphenol A as solvent cut 75% in Xylene. The resin is similar to solid resin Razeen® SR 5072 in performance.

Razeen® SR 5004 is a solid medium molecular weight epoxy resin based on Bisphenol A.

Genable® 3001 dispersion consists of graphene nanoplatelets stabilized in epoxy resin (EEW = 250g/eq.). The graphene nanoplatelets are a synthesized form of graphene produced by a patented process. A formulation-ready Genable® epoxy resin, Genable® 3001 dispersion has been developed to enhance the anti-corrosion performance of coatings on steel substrates by the use of a patented active, non-metallic anti-corrosion additive.

Addison Clear Wave Coatings AC A1428 is a UV-curable epoxy sealant.

HexPly® 914 is a highly successful modified epoxy matrix which is used extensively in high temperature resistant primary aircraft structures. The controlled melt viscosity and excellent matrix rheology of HexPly® 914 permits a wide range of processing conditions for high quality components.

EF 12 is above 240 °C. High Tg EF12 resin system is used to produce structural prepregs. Optimized cure methods for these resin systems are Press and Autoclave molding.

Toray E650 is a low temperature curing toughened resin system pre-impregnated into high performance fibers such as carbon, glass and aramid. It is designed for the production of composite structures in the leisure and sporting industries and also for a range of engineering Applicationss. Toray E650 is compatible for co-cure with Toray’s low temperature cure resin film, Toray EF44, and Toray’s low temperature cure syntactic core, Toray MicroPly™ LT64.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

Acculam™ Epoxyglas G11 nonFR comprised of heat resistant/halogen free epoxy resin and a woven fiberglass substrate. It qualifies to NEMA G11 and MIL-I-24768/3This material exhibits extremely high mechanical strength at elevated temperatures and has good dielectric loss and electric strength properties under both dry and humid conditions. It is resistant to flow, dimensional change, chemicals and has low moisture absorption.

G-Etronax® EP 11 is the composite material that does it all. G-Etronax® EP 11 as an all-in-one material. This is because the carefully composed resins combined with the glass base result not only in exceptional resistance but also amazing electrotechnical properties, making G-Etronax® EP 11 suitable for countless applications.

QuakeBond™ 220UR-SC (underwater - slow cure) is a two-component high-strength structural epoxy-resin designed for a variety of applications including underwater marine uses. This adhesive system trowels easily and has a non-sag, high-tack consistency both in ambient and underwater conditions. QuakeBond™ 220UR-SC is a 100% solids formulation with low toxicity and low odor during cure and features a unique pot life of 90-minutes for applications where extended working time is required.

Havel Composites CZ sro Epoxy resin L (R&G) is Resin suitable for the saturation of glass, aramide, carbon fibers and fabrics. With recommended hardeners it creates a lamination system which showes a good adhesion to wood, metal, sthyropol and other similar materilas.

Poly Lining Systems PLS 477FC is a fast cure polyamide epoxy with high solid content which is capable of achieving a high build. It is designed for application to concrete and steel substrates. Steel substrates do not require extensive preparation prior to application. PLS 477FC is a semi-gloss material which can be provided in a wide range of colors. Not for use in potable water applications.

SMCarbon® 80CF40-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Lattice Composites LCWR-1.5 is highly toughened, higher Tg version of LCWR-1.

APCM SG 4528-040CU-103V is a heavy weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Havel Composites CZ sro Epoxy resin LH 289 with an extremely low viscosity. When curing offers high-quality application properties such as optimum mechanical properties, good chemical resistance, excellent thermal properties etc. It is suitable for the production of composites as well as a top coat of artificial stone. At normal storage temperatures, crystallize does not occur.

Toray BT250E-6 resin system is a 121°C (250°F) cure epoxy prepreg with excellent strength and stiffness. It provides an outstanding surface finish under vacuum bag/oven cure. BT250E-6 has an FAA-conformed database on carbon IM-7 uni-directional tape, S2-glass, and AS-4C plain weave.

Drew Paints 54 Series Epoxy Polyamide Primer is a high performance epoxy primer that is designed to be applied to blasted steel substrates. Drew 54 Series has good chemical resistance for splash/spill exposure.

Cryogenic grade G-10 epoxy-glass

Features Highest stiffness available Heat and abrasion resistant Excellent chemical resistance Great for windtunnel models, jigs and fixtures

VisiJet® CR-WT Rigid White ABS-like Material Extreme durability High rigidity High temperature resistance

LAM-125 / LAM-237 has Low viscosity for quick wet out of synthetic composite fabrics; especially effective with Kevlar® and carbon fiber.

EP GC 308 SY is a woven glass cloth epoxy (epoxide) resin.

Tapecoat® 7100 Wet Bond Epoxy is a two-part 100% solids epoxy.