Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features
- Single component
- High strength
- High elongation
- High adhesion
- Excellent waterproofing properties
- Withstands extreme environmental conditions
- Low odor during application and cure
- Benefits
- Easy application
- No mixing in curing agent
- Resilient to expansion and contraction of substrate high adhesion
- Stress-relieving
- Crack bridging membrane provides 100% contact
- Eliminates migratory water problems designed for demanding exterior applications
- Product Highlights
Basic Uses: : ELASTA-TUFF 5000 is the standard Base Membrane used in most of the ELASTA-TUFF Vehicular Traffic Bearing and Pedestrian Deck Coating systems.
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Installation
Surface Preparation: All substrates must be free of all contaminants and should be primed with TUFFLEX water-based or TUFFLEX solvent-based epoxy primers prior to the application of ELASTA-TUFF 5000. Apply primers at a rate of 250-350 square feet per gallon depending upon substrate porosity or surface profile.
Application: ELASTA-TUFF 5000 is normally applied at a rate of 40 to 50 square feet per gallon, per coat; resulting in a 32 to 40 mil wet film thickness. When applying onto sloped or uneven surfaces, two or more coats of the standard ELASTA-TUFF 5000 Base Coat are required for this coverage. Allow a minimum of 16 to 24 hours cure time between coats. ELASTA-TUFF 5000 is easily applied by squeegee, roller or notched trowel. ALWAYS FOLLOW BY BACKROLLING. Application should not commence unless the ambient temperature is 45°F or higher, and should not proceed during inclement weather. ELASTA-TUFF 5000 is usually used in conjunction with ELASTA-TUFF 6000-AL Aliphatic Top Coats. TUFFLEX Accelerators may be added to ELASTA-TUFF 5000 to compensate for slower cure time in cold weather or for a shortened cure time for rehabilitation or repair projects.
Properties
- Color
- Technical Data
Value Units Test Method / Conditions Solid Content (By Weight) 6 - 10 % ASTM D-1353 VOC Content (Mixed Material) 100.0 g/l - Cure Time (77°F, 50% R.H.,32 mils) 24.0 h - Flash Point min. 120 °F ASTM D-93 Tensile Strength 800 - 1000 psi ASTM D-412 Ultimate Elongation 450 - 650 % ASTM D-412 Hardness 60 - 70 Shore A ASTM D-2240 Tear Resistance 125 - 175 lb./in. ASTM D-1004 Adhesive Bond Strength on Primed Concrete (Cohesive Failure) 195.0 psi ASTMD-903 Viscosity (77°F) 50 - 90 Poise - Weight 10.2 - 10.6 lbs./gal ASTM D-1475
Safety & Health
- Precautions
Exposure to urethanes or petroleum solvents may cause allergic skin or respiratory reactions. Do not get into eyes, onto skin or clothing. If contact occurs, flush affected areas with soap and water. Wash clothing before reuse. Use only with adequate ventilation. Seek medical help for all over exposures.
Storage & Handling
- Limitations
Containers that have been opened must be used within one or two days since the product is a moisture-reactive material that will gel or set up when exposed to moisture in the air. A polyethylene sheet should be used as a blanketing material prior to resealing the lid on a partially used container. Prior to the application of ELASTA-TUFF 5000, proper surface preparation procedures must be followed. Refer to the TUFFLEX Technical Bulletin on Surface Preparation of Plywood and Concrete Substrates. ELASTA-TUFF 5000 cures faster when applied during warm weather and high humidity conditions and slower during cool temperatures and low humidity conditions. The rate of cure may be accelerated by incorporating TUFFLEX Accelerators.
- Shelf Life
Nine (9) months after manufacture when continuously stored in unopened metal pails at temperatures under 80ºF. Stir thoroughly prior to use.