Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ 58 MPa ASTM D638 Tensile Stress (Break, Type I, 50 mm/min) ¹¹ 57 MPa ASTM D638 Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ 5 % ASTM D638 Tensile Strain (Break, Type I, 50 mm/min) ¹¹ 90 % ASTM D638 Tensile Modulus (at 50 mm/min) ¹¹ 2200 MPa ASTM D638 Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ 85 MPa ASTM D790 Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ 2100 MPa ASTM D790 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.18 - ASTM D792 Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ 0.4 - 0.8 % SABIC method Mold Shrinkage (xflow, 3.2 mm) ᵍ ¹¹ 0.4 - 0.8 % SABIC method Melt Flow Rate (at 300°C, 1.2 kgf) ¹¹ 14 g/10 min ASTM D1238 Density ¹¹ 1.19 g/cm³ ISO 1183 Water Absorption (at 23°C, saturated) ¹¹ 0.12 % ISO 62-1 Moisture Absorption (at 23°C, 50% RH) ¹¹ 0.09 % ISO 62 Melt Volume Rate (at 300°C, 1.2 kg) ¹¹ 13 cm³/10 min ISO 1133 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 117 °C ASTM D648 Ball Pressure Test (at 123°C to 127°C) ¹¹ Pass - IEC 60695-10-2 Vicat Softening Temperature (Rate B/120) ¹¹ 138 °C ISO 306 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Notched, at 23°C) ¹¹ 750 J/m ASTM D256 Izod Impact (Notched, at -30°C) ¹¹ 600 J/m ASTM D256 - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 120 °C - Drying Time ⁷ 3 - 4 Hrs - Drying Time (Cumulative) ⁷ 48 Hrs - Maximum Moisture Content ⁷ 0.02 % - Melt Temperature ⁷ 295 - 315 °C - Nozzle Temperature ⁷ 290 - 310 °C - Front - Zone 3 Temperature ⁷ 295 - 315 °C - Middle - Zone 2 Temperature ⁷ 280 - 305 °C - Rear - Zone 1 Temperature ⁷ 270 - 295 °C - Mold Temperature ⁷ 70 - 95 °C - Back Pressure ⁷ 0.3 - 0.7 MPa - Screw Speed ⁷ 40 - 70 rpm - Shot to Cylinder Size ⁷ 40 - 60 % - Vent Depth ⁷ 0.025 - 0.076 mm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Country Availability
- Regional Availability