Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Key Attributes
- Permanent static dissipative coating
- Non-flammable, low odor, and low VOC
- Ready to spray
- Meets ANSI/ESD-S20.20
- Reworkable
- Strong adhesion with excellent flexibility
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Cure Method
- Recommended Preparation
Plastic - Clean the substrate with Isopropyl Alcohol, MG #824, so the surface is free of oils, dust, and other residues.
Drywall - For new drywall, apply directly on top of the drywall primer, after the primer has properly cured. When applying on top of existing paint, first wash the wall with a solution of T.S.P. diluted with water at a 1:10 ratio, to ensure good adhesion.Paint Roller
This product may be applied with a standard paint roller. Thinning is not required.
Manual Spray Guns
Use a standard fluid nozzle gun to spray the diluted paint. The settings listed below are recommendations; however, performance will vary with different brands:
LVMP HVLP Nozzle tip diameter 1.2–1.4 mm 1.2–1.4 mm
Inlet pressure 5–15 psi 5–15 psi Air flow 10–15 SCFM 8.3 SCFM
Air cap 5–10 psi 5–10 psi When using a pressure pot and agitator, keep the agitator at low mixing speed with air pressure of 20–50 psi. Use the lowest pressure necessary to keep the particles suspended.
Selective Coating
For higher volume applications, paint can be applied via selective coating equipment. Use a system with constant fluid recirculation to keep the particles from settling in the lines. A fluid nozzle ranging from 1.2 mm–1.4 mm diameter and 5–10 psi fluid pressure is recommended depending on nozzle size. Thin the paint to adjust the viscosity to the level appropriate for the valve being used.
Clean-up
Clean the spray system and equipment with tap water after use.
Properties
- Color
- Physical Form
- Physical Properties
Value Units Test Method / Conditions Density 1.03 g/mL - - Typical Properties
Value Units Test Method / Conditions Viscosity (at 25 ˚C) 128 cP - Calculated VOC 71.3 g/L - - Cured Properties
Value Units Test Method / Conditions Surface Resistance (at 50 μm) 5.6 x 10⁷ Ω/sq - Service Temperature Range -40 to 120 ˚C - - Uncured Properties
Value Units Test Method / Conditions Percent Solids 29 % -
Regulatory & Compliance
- Certifications & Compliance
- Quality Standards
Technical Details & Test Data
- Cure Instructions
Cure the paint in an oven at one of these time/ temperature options:
Temperature 45 °C 65 °C 80 °C Time 45 min 30 min 10 min - Usage Parameters
Recoat Time 5 min Cure Times 45 min @ 45 ˚C
30 min @ 65 ˚C
10 min @ 80 ˚C
Recommended Film Thickness 50 μm Minimum Film Thickness 40 μm Theoretical Coverage @ 2 mil 36000 cm2/L
Packaging & Availability
- Packaging Type
- Packaging and Supporting Products
Cat. No. Packaging Net Volume Net Weight 844WB-850ML Can 850 mL 878 g 844WB-3.6L Can 3.60 L 3.72 kg
Storage & Handling
- Shelf Life
- 2 Years
- Storage
Store between 4 and 40 ˚C in a dry area, away from sunlight (see SDS).