Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Key Attributes
- High thermal conductivity
- Flame retardant – meet UL 94V-0
- 1:1 mix ratio
- Provides strong electrical insulation
- Excellent compressive and tensile strength
- Bonds well to a wide variety of substances
- Strong resistance to humidity, salt water, mild
- bases, and aliphatic hydrocarbons
- SVHC-free
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Cure Method
- Recommended Preparation
Clean the substrate with Isopropyl Alcohol, MG #824, so the surface is free of oils, dust, and other residues.
- Syringe or Cartridge
1. Twist and remove the cap from the syringe or cartridge. Do not discard cap.
2. Dispense a small amount to ensure even flow of both parts. A manual or pneumatic dispensing gun is required for a 50 mL cartridge.
3. (Optional) Attach a static mixer.
a. Dispense and discard 3 to 5 mL of the product to ensure a homogeneous mixture.
b. After use, dispose of static mixer.
4. Without a static mixer, dispense material on a mixing surface or container, and thoroughly mix parts A and B together.
5. To stop the flow, pull back on the plunger.
6. Clean nozzle to prevent contamination and material buildup.
7. Re-place the cap on the syringe or cartridge.
Properties
- Color
- Physical Form
- Thermal Properties
Value Units Test Method / Conditions Thermal Conductivity (at 25 ˚C) 1.1 W/(m·K) - - Typical Properties
Value Units Test Method / Conditions Mix Ratio 1:1 Volume - Mix Ratio 1:1 Weight - Service Cure 90 Minutes - Viscosity (at 25 ˚C)ᴬ 143 Pa·s - Viscosity (at 25 ˚C)ᴮ 1400 Pa·s - Working Time 20 Minutes - - Cured Properties
Value Units Test Method / Conditions Compressive Strength 125 N/mm2 - CTE After Tg 155 ppm/˚C - CTE Prior Tg 32 ppm/˚C - Glass Transition Temperature (Tg) 39 ˚C - Hardness Shore D 88 - - Lap Shear (Aluminum) 4 N/mm2 - Lap Shear (Stainless steel) 6.4 N/mm2 - Resistivity 1.2 x 10¹² Ω·cm - Service Temperature Range -50 to 165 ˚C - Tensile Strength 29 N/mm2 - - Uncured Properties
Value Units Test Method / Conditions Mixed Density 1.74 g/mL - - Cure Instructions
Allow to cure at room temperature for 16 hours, or cure the adhesive in an oven at one of these time/temperature options:
Temperature 65 °C 80 °C Time 20 minutes 10 minutes
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
Packaging & Availability
- Packaging Type
- Available Packaging
Cat. No. Packaging Net Vol. Net Wt. 8349TFM-25ML Dual Syringe 25 mL 44.6 g 8349TFM-50ML Dual Cartridge 46 mL 82.0 g - Dispensing Accessories
Consult the table below for accessory selection. See the Dispensing Accessories Application Guide for usage instructions. 8MT-50-FT should only be used with a pneumatic dispenser.
Cat. No. Dispensing Gun Static Mixer 8349TFM-25ML N/A N/A 8349TFM-50ML 8DG-50-1-1 8MT-50
Storage & Handling
- Storage and Handling
- Store between 16 and 27 ˚C in a dry area, away from sunlight (see SDS). To maximize shelf life, recap product firmly when not in use.