Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Key Attributes
- High thermal conductivity
- Long working time
- Provides strong electrical insulation
- Bonds well to a wide variety of substances
- Strong resistance to humidity, salt water, mild bases, and aliphatic hydrocarbons
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Cure Method
- Recommended Preparation
Clean the substrate with Isopropyl Alcohol, MG #824, so the surface is free of oils, dust, and other residues.
Syringe or Cartridge
- Twist and remove the cap from the syringe or cartridge. Do not discard cap.
- Dispense a small amount to ensure even flow of both parts. A manual or pneumatic dispensing gun is required for a 50 mL cartridge.
- (Optional) Attach a static mixer.
- Dispense and discard 3 to 5 mL of the product to ensure a homogeneous mixture.
- After use, dispose of static mixer.
- Without a static mixer, dispense material on a mixing surface or container, and thoroughly mix parts A and B together.
- To stop the flow, pull back on the plunger.
- Clean nozzle to prevent contamination and material buildup.
- Re-place the cap on the cartridge or syringe.
Dispensing Accessories
Consult the table below for accessory selection. See the Dispensing Accessories Application Guide for usage instructions. 8MT-50-FT should only be used with a pneumatic dispenser.
Cat. No. Dispensing Gun Static Mixer 8329TFS-25ML N/A N/A 8329TFS-50ML 8DG-50-1-1 8MT-50, 8MT-50-FT
Properties
- Color
- Physical Form
- Thermal Properties
Value Units Test Method / Conditions Thermal Conductivity (at 25 ˚C) 1.2 W/(m·K) - - Typical Properties
Value Units Test Method / Conditions Viscosity (at 25 ˚C)ᴮ N/A - - Viscosity (at 25 ˚C)ᴬ 700 Pa·s - - Cured Properties
Value Units Test Method / Conditions Resistivity 1 x 10¹² Ω·cm - Hardness Shore D 68 - - Tensile Strength 4.2 N/mm2 - Compressive Strength 42 N/mm2 - Lap Shear (Stainless steel) 5 N/mm2 - Lap Shear (Aluminum) 6.3 N/mm2 - Glass Transition Temperature (Tg) 9 ˚C - CTE Prior Tg 47 ppm/˚C - CTE After Tg 164 ppm/˚C - Service Temperature Range -40 to 150 ˚C - - Uncured Properties
Value Units Test Method / Conditions Mixed Density 2.11 g/mL -
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
Technical Details & Test Data
- Cure Instructions
The product will not cure at room temperature. Cure the adhesive in an oven at one of these time/ temperature options:
Temperature 65 °C 80 °C 100 °C Time 3 hours 80 minutes 30 minutes - Usage Parameters
Working Time 4 h Mix Ratio by Volume 1:1 Mix Ratio by Weight 1:0.96
Packaging & Availability
- Packaging Type
- Packaging and Supporting Products
Cat. No. Packaging Net Volume Net Weight 8329TFS-25ML Dual Syringe 25 mL 52.2 g 8329TFS-25ML Dual Cartridge 45 mL 94 g
Storage & Handling
- Shelf Life
- 3 Years
- Storage and Handling
Store between 16 and 27 ˚C in a dry area, away from sunlight (see SDS). To maximize shelf life, recap product firmly when not in use.