Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Key Attributes
- High thermal conductivity
- Flame retardant—UL 94V-0 registered (File # E334302)
- 1:1 mix ratio
- Provides strong electrical insulation
- Low CTE prior Tg
- High tensile and compressive strength
- Bonds well to a wide variety of substances
- Strong resistance to humidity, salt water, mild bases, and aliphatic hydrocarbons
Applications & Uses
- Markets
- Applications
- Application Area
- Compatible Substrates & Surfaces
- Cure Method
- Recommended Preparation
Clean the substrate with Isopropyl Alcohol, MG #824, so the surface is free of oils, dust, and other residues
Syringe or Cartridge
- Twist and remove the cap from the syringe or cartridge. Do not discard cap.
- Dispense a small amount to ensure even flow of both parts. A manual or pneumatic dispensing gun is required for a 50 mL cartridge.
- (Optional) Attach a static mixer.
- Dispense and discard 3 to 5 mL of the product to ensure a homogeneous mixture.
- After use, dispose of static mixer.
- Without a static mixer, dispense material on a mixing surface or container, and thoroughly mix parts A and B together.
- To stop the flow, pull back on the plunger.
- Clean nozzle to prevent contamination and material buildup.
- Re-place the cap on the cartridge or syringe or cartridge.
Dispensing Accessories
Consult the table below for accessory selection. See the Dispensing Accessories Application Guide for usage instructions. 8MT-50-FT should only be used with a pneumatic dispenser.
Cat. No. Dispensing Gun Static Mixer 8329TFF-25ML N/A N/A 8329TFF-50ML 8DG-50-1-1 8MT-50, 8MT-50-FT
Properties
- Physical Form
- Thermal Properties
Value Units Test Method / Conditions Thermal Conductivity (at 25 ˚C) 0.8 W/(m·K) - - Typical Properties
Value Units Test Method / Conditions Viscosity (at 25 ˚C)ᴬ 72 Pa·s - Viscosity (at 25 ˚C)ᴮ 110 Pa·s - - Cured Properties
Value Units Test Method / Conditions Resistivity 7.9 x 10¹² Ω·cm - Hardness Shore D 82 - - Tensile Strength 13 N/mm2 - Compressive Strength 65 N/mm2 - Lap Shear (Stainless steel) 7.1 N/mm2 - Lap Shear (Aluminum) 8.3 N/mm2 - Glass Transition Temperature (Tg) 25 ˚C - CTE Prior Tg 34 ppm/˚C - CTE After Tg 146 ppm/˚C - Service Temperature Range -40 to 150 ˚C - - Uncured Properties
Value Units Test Method / Conditions Mixed Density 1.63 g/mL -
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
Technical Details & Test Data
- Cure Instructions
Allow to cure at room temperature for 4 hours, or cure the adhesive in an oven at one of these time/ temperature options :
Temperature 65 °C 80 °C Time 15 minutes 10 minutes - Usage Parameters
Working Time 5 min Service Cure 5 h @ 22 ˚C Mix Ratio by Volume 1:1 Mix Ratio by Weight 1:0.9
Packaging & Availability
- Packaging Type
- Available Packaging
Cat. No. Packaging Net Volume Net Weight 8329TFF-25ML Dual Syringe 25 mL 40.1 g 8329TFF-50ML Dual Cartridge 45 mL 72.3 g
Storage & Handling
- Shelf Life
- 3 Years
- Storage
Store between 16 and 27 ˚C in a dry area, away from sunlight (see SDS). To maximize shelf life, recap product firmly when not in use.