Products

Special compound for 3D effect painting based on PP, e.g. B. For decorative applications in the automotive exterior.

KEBABLEND / H 21.1200 PP is a functional compound based on PP with high density.

BARLOG plastics GmbH Keballoy® EP 23 is an unreinforced ABS / PC polymer blend, which is particularly suitable for the production of sophisticated chrome-plated components. It is also optimized for very good adhesion of the electroplating layer and has a wide process window.

PBT-GF30 FR, PBT, 30% glass fiber reinforced, flame retardant

Polyester elastomer, Shore D35

BARLOG plastics GmbH Kebaform® / C 25 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Kebaform® / C 25 H improves the sliding and wear behavior solely by modifying the polymer chain and there is no reduction in mechanical properties due to the addition of tribologically active additives. Due to its property profile, Kebaform® / C 25 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

BARLOG plastics GmbH Kebaflow® LCP MX130 is an LCP reinforced with 30% short glass fiber / mineral mixture with very high heat resistance. The material is characterized by the following properties: good flowability with thin walls, very good toughness and strength, inherently flame retardant, high heat resistance (HDT ~ 270 °C), good chemical resistance.

PBT unreinforced, flame retardant

BARLOG plastics GmbH Kebablend® / MW 39.1500 PPA is a product based on PPA for the production of soft magnetic components. The achievable permeability is approx. 60 (at 1 MHz) and the saturation flux density is approx. 430 mT.

TPE-S, Shore A60, natural

KEBABLEND / H 27.1200 PBT is a functional compound based on PBT with high density.

PPS functional compound for the production of plastic-bonded magnets

PPS-GF40, linear PPS, 40% glass fiber reinforced, approved for food applications according to EU and FDA guidelines.

POM-CF20, POM copolymer, medium viscosity, carbon fiber reinforced, electrically conductive

TPE-S, Shore A80

PBT + X-GF45, 45% glass fiber reinforced, optimized surface quality, improved weld line strength and reduced tendency to warp, color settings with approval for food contact available.

TPE-S, Shore A40, black

PPS functional compound for the production of plastic-bonded magnets

PPS functional compound for the production of plastic-bonded magnets

TPE-S, Shore A80

TPE-S, Shore A60, black, improved compression set at high temperatures

PBT unreinforced, highly impact modified

BARLOG plastics GmbH Kebablend® / WR XB 111001/12 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

BARLOG plastics GmbH Kebablend® / WR XB 111001/1 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

BARLOG plastics GmbH Kebaflex® / SG 85.E A.02 is a TPE-S, Shore A86, extrusion. It is available in various Shore hardnesses from below A10 to more than D50 and is often used as a substitute for rubber due to the cost-effective processing in the injection molding process. It is soft and flexible, can be colored freely, shows good elastic behavior up to 100°C and is pleasant to the touch. A wide range of modified compounds is available, e.g. adhesion-modified types for 2K injection molding, printable types, variants with optimized compression set, etc.

PBT functional compound, electrically conductive

PBT-GF30, PBT, 30% glass fiber reinforced

BARLOG plastics GmbH Kebablend® / WR 02/2110 is a special compound based on POM homopolymer, which has very good sliding behavior and high wear resistance. The material has medium strength and a high elongation at break and, compared to POM copolymer, an increased melting temperature and heat resistance.

PBT unreinforced, injection molding type, approved for use in contact with food

POM copolymer unreinforced, medium viscosity

POM copolymer unreinforced, highly viscous for injection molding and extrusion processing

POM copolymer unreinforced, medium viscosity, UV stabilized

BARLOG plastics GmbH Kebaform® / C 130 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Due to its property profile, Kebaform® / C 130 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow any compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

BARLOG plastics GmbH Kebablend® / WR FE 190202 is a special compound based on PA66 that combines high strength and impact resistance with good sliding behavior and high wear resistance.

KEBABLEND / WR XB 111001/5 is a special compound based on POM, which has very good sliding behavior and high wear resistance.

BARLOG plastics GmbH Keballoy® / EP FE 170404 is an unreinforced ABS / PC polymer blend, which is particularly suitable for the production of sophisticated chrome-plated components. It is also optimized for very good adhesion of the electroplating layer and has a wide process window. In addition, it has an increased heat resistance compared to Keballoy® / EP23 and an improved flow compared to Keballoy® / EP 23 and Keballoy® / EP 25.