Products in Water Treatment Chemicals: Industrial Water Treatment

USALCO Aluminum Sulfate Solution is manufactured by dissolving alumina trihydrate (ATH) in water and sulfuric acid. To ensure the highest quality of this product, stringently selected raw materials and state-of-the-art manufacturing practices are used. USALCO Alum meets the specifications of the American Water Works Association Standard B403‐16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals ‐ Health Effects at a maximum dosage of 150 mg/L.

DelPAC® 2950 is widely accepted as the preferred polyaluminum chloride for cost-effective improvement of finished water quality. As a coagulant, it enhances filter performance, potentially eliminates the need for pH adjustment with alkalis, and decreases sludge residuals. It meets the specifications of American Water Works Association Standard B408-18 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dosage of 250 mg/L.

AlcoPAS™ 1000 is a medium-basicity, advanced ultra-low-chloride, aluminum-based coagulant and flocculant for treating potable water, industrial process water, and wastewater. It is a clear to slightly hazy, colorless to light-beige aqueous solution. This product can be certified to NSF/ANSI Standard 60 for the treatment of potable water.

DelPAC® 2500 is a highly regarded polyaluminum chloride solution that is known for its cost-effectiveness in enhancing the quality of finished water. As a coagulant, it can extend filtration runs, minimize or eliminate the requirement for alkali pH adjustment, and decrease sludge residuals. It conforms to the American Water Works Association Standard B408-18 and NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 250 mg/L.

DelPAC® 2000 is a widely accepted polyaluminum chloride that is known for its cost-effective ability to improve finished water quality. As a coagulant, it can offer longer filtration runs, minimize or eliminate the need for pH adjustment with alkalis, and reduce sludge residuals. It complies with American Water Works Association Standard B408-18 and NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 250 mg/L.

USALCO Aluminum Chloride is a solution that is very effective in drinking water treatment, removal of phosphorus from municipal/industrial wastewater, and as an intermediate chemical in the manufacturing of various products. This product complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects at a maximum dosage of 250 mg/L.

USALCO Dry Aluminum Sulfate (Low Iron Grade) is produced using advanced techniques and high-quality materials to meet the highest quality standards. USALCO also produces dry alum in various other grades (iron-free and FCC-grade) and custom granular sizes to meet a wide range of applications. This product is used in water treatment, dye production, leather tanning, papermaking, and other industrial applications. It adheres to the American Water Works Association Standard B403-16 and meets the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dosage limit of 150 mg/L.

USALCO Sodium Aluminate (Granular) is a white powder that easily dissolves in water and is the dry form of sodium aluminate. It is produced by mixing alumina trihydrate with sodium hydroxide to create a solution, which is then solidified by removing excess moisture. This product does not contain any stabilizing agents.

DelPAC® 3030 Polyaluminum Chloride is an advanced aluminum-based coagulant used for municipal drinking, wastewater treatment, as well as for the treatment of industrial process water. When used as a coagulant, it can provide longer filter runs, reduce or eliminate the need for alkali pH adjustment chemistry, and minimize coagulant sludge residuals. It also helps in the removal of suspended and dissolved matter, such as organics and phosphorus.

USALCO Ferric Sulfate (50%) is an effective liquid coagulant that is based on trivalent iron (Fe3+). It is produced by the reaction of high-purity iron ore with sulfuric acid. The product is effective for clarifying both drinking water and wastewater and can be used for removing turbidity, color, phosphate, and heavy metals. It is used in lime softening processes and for sludge treatment.

USALCO Ferric Sulfate (60%) is a highly effective liquid coagulant based on trivalent iron (Fe3+). It is made by reacting high-purity iron ore with sulfuric acid. The product can be used to clarify both potable water and wastewater, removing turbidity, color, phosphate, and heavy metals. It is used in lime softening processes and for conditioning sludge. It also has the ability to control hydrogen sulfide, reduce odor, and prevent corrosion.

USALCO Dry Aluminum Sulfate (Iron Free Grade) is manufactured using a state-of-the-art process and high-quality raw materials, which ensures that the product meets the highest quality standards. USALCO also produces dry alum in various other grades (low-iron and FCC-grade) and in specialty granular sizes to satisfy even the most difficult applications. USALCO's dry alum is used in water treatment, colors and dyes, leather tanning, papermaking, and many other industrial applications. It meets the specifications of the American Water Works Association Standard B403-16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects at a maximum dosage of 150 mg/L.

USALCO Dry Aluminum Sulfate (Rice Grind) is manufactured using state-of-the-art processes and high-quality raw materials to ensure that the product meets the highest quality standards. USALCO offers various grades of dry alum, including low-iron, iron-free, and FCC grades, as well as specialty granular sizes to meet a wide range of applications. This product is used in water treatment, dye production, leather tanning, and papermaking, among other industrial applications. It meets the specifications of the American Water Works Association Standard B403-16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 150 mg/L.

DelPAC® 2450 is a widely accepted polyaluminum chloride solution that is known for its cost-effective benefits in improving water quality. As a coagulant, it can provide longer filtration runs, minimize the need for pH adjustment with alkali, and decrease the amount of sludge residuals. This product meets the standards set by the American Water Works Association Standard B408-18 and complies with NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects at a maximum dosage of 250 mg/L.

DelPAC® 1842 is an advanced formulation of basic polyaluminum chloride that has demonstrated exceptional effectiveness in the treatment of drinking water and the elimination of phosphorus in municipal and industrial wastewater systems. It conforms to the specifications outlined in the American Water Works Association Standard B408-18 and meets the criteria established in NSF/ANSI 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dose of 250 mg/L.

USALCO Dry Aluminum Sulfate (Purified Grade) is manufactured to meet high-quality standards using advanced processes and premium raw materials. It comes in various grades, including low-iron, iron-free, and FCC grades, and in special granular sizes to meet diverse needs. It is utilized in industries such as water treatment, dye production, leather tanning, papermaking, and others. This dry alum meets the American Water Works Association Standard B403-16 and follows NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 150 mg/L.

DelPAC® XG (Aluminum Chlorohydrate) is a highly effective coagulant that is used in water and wastewater treatment. DelPAC® XG is proven to be an excellent option for removing organic matter, TSS, and copper. It is known for its high concentration and basicity, making it effective in removing organic matter and performing well over a wide pH range. This product meets the standards set by the American Water Works Association Standard B408-18 and complies with the health effects requirements of NSF/ANSI/CAN 60, with a maximum recommended dosage of 250 mg/L.

DelPAC® 1525 is an advanced formulation of basic polyaluminum chloride that has demonstrated exceptional effectiveness in the treatment of drinking water and the elimination of phosphorus in municipal and industrial wastewater systems. It conforms to the specifications outlined in the American Water Works Association Standard B408-18 and meets the criteria established in NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum dose of 250 mg/L.

USALCO EPI-DMA polyamines are cationic polyquaternary amines with a solid content of 49 - 56%. The viscosity of this product can vary from low (100 cps) to high (9,000 cps) depending on the molecular weight. These polyamines are effective as flocculants and coagulants in the clarification of raw water and wastewater and also serve as filter aids in the treatment of raw water and wastewater. They are certified to NSF/ANSI/CAN Standard 60 for use up to 10 mg/L in potable water and comply with ANSI/AWWA Standard B452-14.

USALCO Ferrous Sulfate (7%) is a liquid coagulant that contains 7% bivalent iron (Fe2+). It is produced through the reaction of high-purity iron ore and metallic iron with sulfuric acid. This product is used in the treatment of municipal and industrial water and wastewater. It has various applications, including reducing hydrogen sulfide, controlling chromate and cyanide, de-chlorination, conditioning sludge, and precipitating phosphate with aeration.

DelPAC® 2020 is a highly effective polyaluminum chloride solution for improving the quality of finished water. As a coagulant, it can offer longer filtration runs, minimize or eliminate the need for pH adjustment with alkalis, and decrease sludge residuals. This product adheres to the standards set by the American Water Works Association Standard B408-18 and meets the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals - Health Effects with a maximum recommended dosage of 250 mg/L.

USALCO Sodium Aluminate Solution (38%) is an economical source of highly reactive alumina manufactured by dissolving alumina tri‐hydrate (ATH) into sodium hydroxide and water. USALCO 38 is also stabilized to prevent alumina from precipitating. The use of only stringently selected raw materials and state‐of‐the‐art manufacturing practices ensures that USALCO 38 is of the highest quality. USALCO 38 meets the specifications of the American Water Works Association Standard B405‐16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals ‐Health Effects at a maximum dosage of 105 mg/L.

USALCO Poly-DADMAC is a cationic polyquaternary amine with a solid content in the range of 15 - 40%. Its viscosity can vary from low (10 cps) to high (3000 cps) depending on the molecular weight. It is highly effective as a flocculant and coagulant for raw water/wastewater clarification and also serves as a filter aid in raw water/wastewater treatment. This product is certified to NSF/ANSI Standard 60 for use in potable water, with concentrations ranging from 25 mg/L to 50 mg/L, depending on the product.

USALCO Sodium Aluminate Solution (45%) is an economical source of highly reactive alumina manufactured by dissolving alumina tri‐hydrate (ATH) into sodium hydroxide and water. USALCO 45 is also stabilized to prevent alumina from precipitating. The use of only stringently selected raw materials and state‐of‐the‐art manufacturing practices ensures that USALCO 45 is of the highest quality. USALCO 45 meets the specifications of the American Water Works Association Standard B405‐16 and complies with the requirements of NSF/ANSI/CAN 60: Drinking Water Treatment Chemicals ‐Health Effects at a maximum dosage of 89 mg/L.

USALCO Ferrous Sulfate (5%) is an effective liquid coagulant made from bivalent iron (Fe2+). It is produced through the reaction of high-purity iron ore and metallic iron with sulfuric acid. This solution can be efficiently used as a flocculant and coagulant in the treatment of municipal and industrial water and wastewater. Its applications include controlling hydrogen sulfide, reducing chromate and complexing cyanide, de-chlorination, conditioning sludge, and precipitating phosphate with aeration.

H-PAC® 8323S is a highly effective cationic coagulant for use in industrial and municipal water and wastewater applications for the removal of turbidity, color, suspended solids and phosphorus. It should be stored and handled in suitable non-corrosive materials such as fiberglass, reinforced plastic, PTFE, PVC/CPVC, rubber lined steel or polyethylene.

WWT 4300 is a low-charge, high-molecular-weight, anionic polyacrylamide in emulsion form. This product is used as a flocculant in a wide variety of municipal and industrial wastewater treatment applications. It has been successfully applied in liquid/solids separation systems, including clarification and dewatering.

H-PAC® 7011S is a highly effective cationic coagulant for use in industrial and municipal water and wastewater applications for the removal of turbidity, color, suspended solids, and phosphorus. It should be stored and handled in suitable non-corrosive materials such as fiberglass, reinforced plastic, PTFE, PVC/CPVC, rubber-lined steel, or polyethylene.

WWT 4690 is a high-charge, standard molecular-weight, cationic polyacrylamide in dry form. This product is used as a flocculant in a wide variety of municipal and industrial wastewater treatment applications. It has been successfully applied in liquid/solids separation systems, including clarification and dewatering.

H-PAC® E8320 is a highly effective cationic coagulant for use in industrial and municipal water and wastewater applications for the removal of turbidity, color, suspended solids and phosphorus. It should be stored and handled in suitable non-corrosive materials such as fiberglass, reinforced plastic, PTFE, PVC/CPVC, rubber lined steel or polyethylene.

H-PAC® 5512 is a highly effective cationic coagulant for use in industrial and municipal water and wastewater applications for the removal of turbidity, color, suspended solids and phosphorus.

WWT 221 is a high charge, high molecular weight anionic polyacrylamide in dry form. It is used as a flocculant in a wide variety of municipal and industrial wastewater treatment applications, and has been successfully applied in liquid/solids separation systems, including clarification and dewatering.

H-PAC® 7012S is a highly effective cationic coagulant for use in industrial and municipal water and wastewater applications for the removal of turbidity, color, suspended solids, and phosphorus. It should be stored and handled in suitable non-corrosive materials such as fiberglass, reinforced plastic, PTFE, PVC/CPVC, rubber-lined steel, or polyethylene.

Aquacros® HC-4030 is a high performance liquid blended zinc and orthophosphate product designed to provide corrosion control in potable and industrial water, reducing corrosion in the distribution system. It saves money by reducing corrosion and decreasing flushing, leaks, and failures, and assists municipalities in meeting the Lead and Copper Rule. It is a Clear Liquid.

WWT 80 is a high-charge, high-molecular-weight, cationic polyacrylamide in dry form. It is used as a flocculant in a wide variety of municipal and industrial wastewater treatment applications. This product has been successfully applied in liquid/solids separation systems, including clarification and dewatering.

WWT 200 is a low charge, medium molecular weight anionic polyacrylamide in dry form. It is used as a flocculant in a wide variety of municipal and industrial wastewater treatment applications, and has been successfully applied in liquid/solids separation systems, including clarification and dewatering.