Products in Other Paints & Coatings Applications: Epoxy & Epoxy Deri...

jER™ YX8000D is a hydrogenated bisphenol A-type liquid epoxy resin with significantly lower chlorine impurity levels than other commercially available products. It can be used for wide variety of optical adhesives and encapsulants.FeaturesExcellent adhesionFast cure timeLow chlorine contentExcellent transparencyLED-curableUV-curableApplicationsConsumer appliances and electronicsElectrical and electronic displaysElectronics adhesivesPotting compoundsSemiconductor manufacturingLEDs*jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

jER™ YX7105 is a liquid-type epoxy resin with toughness, flexibility, and high stretchability. It is used as an impact modifier for semiconductor, printed electronics and wearable devices to avoid bending and warpage. jER™ YX7105 is an adduct formed from the reaction of epichlorohydrin and an aliphatic and aromatic polyol.FeaturesExcellent adhesionGood toughnessGood mechanical, impact and crack resistanceExcellent elasticity and flexibilityApplicationsPrinted electronics (resist ink, build-up wire board, flexible printed wire board, metal core printed circuit board)Semiconductor manufacturing (liquid mold compound, underfill, sidefill, diebonding, ACF, NCF, ACP, NCP)Base film and sheet for wearable devicesCoatingsAdhesives *jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

jER™ YX4000 is a biphenol-type solid epoxy resin with significantly low melt viscosity, low water absorption and a good balance between adhesiveness and rigidity against stress. It can be used for electrical and electronic applications. jERTM YX4000 is an adduct formed from the reaction of epichlorohydrin and tetramethylbiphenol FeaturesAbrasion, heat and water resistanceElectrical insulationWear resistanceProduct HighlightsSignificantly low melt viscosity (melting point: 108°C)Low chroline contentLow water absorption ApplicationsElectrical and electronic applications (EMC, solder resist, PCB)Potting and encapsulation materialsPowder coatings for ship bottomsAdhesivesComposites *jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

jER™ YL980 is is a Bisphenol A-type liquid epoxy resin with very low chlorine content. It can be used for electrical and electronic applications (Sealant, casting agent, adhesives, and so on). Benefits Excellent adhesiveness Maintains high electrical reliability Features Chemical, heat and water resistant Electrical insulating properties Significantly low chlorine content (below 500 ppm) Applications Electrical and electronic applications Potting & encapsulation materials Adhesives *jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

jER™ 1750 is a very low viscosity Bisphenol F-type liquid epoxy resin. It can be used in sealants, casting agents and adhesives in electrical and electronic applications and fiber reinforced plastics, and for liquid underfill and adhesives for semiconductor manufacturing.FeaturesChemical, heat and water resistanceElectrical insulation*jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

jER™ YX8040 is a hydrogenated bisphenol A-type solid epoxy resin, with high molecular weight. It can be used for optical materials such as LED encapsulants and adhesives for displays.FeaturesHigh purityTransparencyLED-curableUV-curable *jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

jER™ YL983U is a Bisphenol F-type liquid epoxy resin with very low chlorine content and low viscosity. It is used for electrical and electronic applications (Sealant, casting agent, adhesives, and so on). BenefitsExcellent adhesivenessGood elastic recovery FeaturesChemical, heat and water resistantElectrical insulating propertiesSignificantly low chlorine content (below 500 ppm)Low viscosityApplicationsElectrical and electronic applications Potting & encapsulation materialsAdhesives *jER™ is provided by Mitsubishi Chemical Corporation, a member of the Mitsubishi Chemical Group.

Additive EP024 73 Wa/BG is an epoxy phosphate additive for waterborne stoving enamels. With this resin it is possible to improve adhesion and resistance to corrosion, chemicals and stains.Features & BenefitsFor waterborne stoving enamelsImprove adhesionImprove resistance to corrosion

Additive EP135 is an epoxy-phosphate ester resin developed as an additive for stoving enamels. This resin improves humidity and corrosion resistance, adhesion, chemical resistance, stain resistance and pasteurization resistance.Features & BenefitsFor stoving enamelsImproves humidity and corrosion resistanceImproves adhesion, chemical resistance

Epoxy functional silane used used to improve dry and wet strength in cured composites reinforced with glass fiber rovings. Silanes are used in a variety of industrial applications. Organofunctional Silanes have an organic functional end group and an alkoxy functional end group which allow the silane to act as a bridge between organic materials and inorganic substrates. The organic functional group is matched to the resin system while the alkoxy group provides the reactive site for crosslinking. These materials are useful as adhesion promoters, crosslinking agents, surface modifiers and hydrophobizing agents.

Andisil® 186 Silane is used in a variety of industrial applications. Organofunctional Silanes have an organic functional end group and an alkoxy functional end group which allow the silane to act as a bridge between organic materials and inorganic substrates. The organic functional group is matched to the resin system while the alkoxy group provides the reactive site for crosslinking. These materials are useful as adhesion promoters, crosslinking agents, surface modifiers and hydrophobizing agents.

Intumax EP200C is a unique two component epoxy fire retardant – intumescent coating based on our proprietary non-halogenated phosphate technology. All of our phosphates are manufactured in house for our exclusive use. When exposed to heat and/or fire, INTUMAX®EP-200C forms a continuous char foam that protects products from both heat and flame. The active ingredients in INTUMAX® products are not water soluble and will not leach out over time. INTUMAX®EP-200C is recommended for use as a base resin for specialty coatings. The viscosity is easily reduced by the addition of solvents. Pigments, anti- settling agents and other flame retardants may also be incorporated.

TCI Powder Coatings OGF Epoxy Hybrid Primer (7820-12396) is an epoxy coating formulated to provide excellent chemical and corrosion resistance, as well as good properties such as adhesion and flexibility. It is ideally suited for interior applications or as a primer. Reduce cure schedule to 5min at 375F if followed by powder top coat. Fully cure as indicated if used with liquid top coat. Pre-test with intended top coat to validate production conditions.

ChemSystems Helix Epoxy Bonder is a two-component water-based epoxy primer and moisture barrier. It is an excellent adhesion promoter between Helix cement-based overlay toppings and hard surface substrates. Helix Epoxy Bonder forms an impermeable membrane that acts as a moisture barrier and provides crack suppression properties. It is a slow cure product (24 hours) and is designed to be surface seeded with 90 mesh sand for optimum adhesion properties with any cement-based overlay.

TCI Powder Coatings MIL Spec Primer 32348 (7820-71737) is a phenolic-cured novolac- modified epoxy coating formulated to provide excellent chemical and corrosion resistance, as well as good properties such as adhesion and flexibility. It is ideally suited for interior applications or as a primer.

TCI Powder Coatings LC Red Oxide Primer (7760-3931) is an epoxy coating formulated to provide excellent chemical and corrosion resistance, as well as good properties such as adhesion and flexibility. It is ideally suited for interior applications or as a primer.

HEPACRETE EPAPOX 22 is a solvent-free system loaded with adhesion promoter, based on modified epoxy resins and special hardeners, milky. Particularly suitable for concrete surfaces.

EPACRETE EPAPOX BUS is a solvent-free three-component system, particularly suitable as an adhesion promoter and impregnating agent for damp cementitious surfaces.

ChemSystems Helix Epoxy Primer is a two component, water-based epoxy primer designed as an adhesion promoter between Helix polymer coatings, cement based overlays, and hard surface substrates. Helix Epoxy Primer acts as a thin build primer, at the same time penetrating the surface of the substrate to provide excellent adhesion.

Razeen® LR 2302 is a medium viscosity Bisphenol A/F based liquid epoxy resin, with a reduced risk of crystalisation on storage at low temperature.

Kukdo Chemical KD-4014 Epoxy Resins are bisphenol-A type half-capped epoxy resin, and designed for applications of high performance powder coating, especially FBE(Fusion Bonded Epoxy coating). The most advantage of these products is that residual bisphenol-A content is the less than one percent by weight. Also, these products have excellent performance of block resistance, chemical resistance and mechanical properties.

RIKARESIN BPO-20E is used in the fields of adhesives, paints and electricity to improve toughness, flexibility and adhesion. Liquid epoxy resin with bisphenol A skeleton. Since it has excellent impregnation properties, it is also used for FRP molding and casting. Improves heat cycle property, thermal shock resistance and shock resistance.

Razeen® LR 2351 is a general purpose modified epoxy resin based on Bisphenol A & Bisphenol F. Razeen® LR 2351 yields excellent mechanical properties and resistance to chemicals, which can be modified within wide limits by using various hardeners and fillers. Razeen® LR 2351 is meets the relevant requirements of the FDA listing.

Super SAP® CCR/CCS is a clear, UV-stabilized epoxy system designed specifically for casting, potting, and embedding applications. Low color and low viscosity allow for bubble-free, crystal-clear castings ideal for art and hobby applications. This Super Sap® Formulation features two hardener speeds: slow (CCS) for high-build casting epoxy applications and fast (CCF) for quick, small project fast casting epoxy applications such as resin jewelry and more.

Intumax EP 102W is a two-part waterborne epoxy intumescent coating. It is engineered to provide a protective coating that combines toughness and wear resistance with low flame spread, low heat transfer and low smoke. In addition, the smoke generated is low in toxicity. The char foam that is formed rises in 20 - 40 seconds. Once this char layer forms, smoke generation is almost entirely eliminated; the burning ceases, and coated surfaces are thermally insulated. Intumax EP102W cures within 24 hours at room temperature to a tack free coating while providing close to 3 hours of working life. For ease of application or for spraying, Intumax EP102W is readily thinned with tap water.

Graxy™ 503 is a type of low molecular weight solid modified epoxy resin polymerized by graphene, epoxy resin and other ingredients. It is designed for use in the production of graphene zinc anti-corrosive primers..

Razeen® LR 2783 is a low viscosity epoxy resin based on Bisphenol A\F modified with aliphatic glycidyl ether.

CHS-EPOXY 101 X 60 is a Fast air drying 60% solution of epoxy ester.

H-101 is a aliphatic Amine Epoxy Adduct Solution.

Super SAP® CLR/CLS is our flagship, high-performance, clear-coating epoxy system. A Super Sap® Formulation, the CLR system is a water-clear, UV-stabilized epoxy system for laminations and coatings that require a low-color, low-yellowing epoxy such as high-colorwork applications. This system features a quick air-release and world-class UV resistance package. CLR works with multiple hardeners to match your working parameters. It has an ideal viscosity for a wide range of applications that use hand layup techniques with fast, room-temperature cures.

Araldite® GY 6010 is a general purpose unmodified epoxy resin based on Bisphenol A with medium viscosity.

Araldite® GZ 280X80 is a semi-solid epoxy resin based on Bisphenol A as solvent cut 80% in Xylene.

Vosschemie Benelux Epoxy Primer Fast A+B is a 2-component, medium viscosity, unfilled epoxy primer with (VOS maximum 1%) for sealing and bonding to almost all substrates. Can be applied in combination with epoxy floor paint or a poured PU floor or coating. Available in 1.5 kg, 3 kg and 10 kg packages.

Polin EP 9011 is a epoxy based, two component, transparent concrete primer without solvent.

BONDiT™ B-536 is a two-part, very high strength, 100% solids, room-temperature curing semi-flexible epoxy resin system. Especially designed for adhesive applications in bonding to a wide range of engineering plastics, including polyolefin and metals, glass, ceramic, composite and wood. Typical example of lapshear bond strength is 1100 PSI for PEEK-to-PEEK and PEEK-to-Steel substrates. B-536 handles harsh environments easily and is effective against moisture, salt water, acids, alkalies, oils, and detergents. B-536 has high thermal stability and offers good corrosion resistance. The semi- flexible properties of B-536 permits assembly of materials with dissimilar thermal expansion and survive thermal cycling. Likewise mechanical vibration, shock and impact are easily absorbed by B-536 and protect surfaces and bonded assemblies.

Razeen® SR 5357 is a Solid epoxy resin based on bisphenol A and phenol novolac for powder coating.