Products in Other Wire & Cable Applications

Plastay DINP (Di Isononyl Phthalate) is usually used with materials such as PVC for plasticization, after heating to a soft or plasticized state, to obtain elasticity, brightness for plastic, create electrical resistance, prevent cracking and make the surface smooth. Do not allow the ingress of materials that will be removed from the mold.

RESBLEND 2 (PA + ABS) is an acrylonitrile butadiene styrene and polyamide (ABS + PA) grade by Polimarky. RESBLEND PA/ABS complies with ISO 9001:2008, ISO 14001:2004 and ISO/TS 16949:2009.

Sylvin™ 7833-65 Black is a vinyl compound formulated for electrical molding applications.

White Masterbatch 152 recommended for injections, Blow moldings, Sheets,Thin Films and Cables

PPA GF20 is a 20% glass fiber reinforced poly phthalamide.

Sylvin Technologies Sylvin™ 916VO-95C White 1441 is a thermoplastic compound formulated for electrical injection molding applications. This compound has a underwriters laboratories listing as a recognized component for all colors.

Polsil® GUM 122/60 is a special grade heat cured elastomer with higher thermal resistance.

Sylvin™ 7868-95 Black is a vinyl compound formulated with FDA sanctioned ingredients for electrical molding applications.

PEROXAN HX-50 PS is 2,5-Dimethyl-2,5-di-(tert-butylperoxy)-hexane 50%, Powder with silica.PEROXAN HX-50 PS is used for the crosslinking of natural rubber and synthetic rubber, as well as polyolefins.

Sylvin Technologies Sylvin™ 9067-82 LMW Gray 9218 is a vinyl compound formulated for injection molding applications. This compound has a underwriters laboratories listing as a recognized component.

White Masterbatch 163 recommended for injections, Blow moldings, Sheets,Thin Films and Cables

JYANOX 1024 Antioxidant is a characteristic of nondiscoloring and has a good synergistic effect with general antioxidant.

JSR BUROMOBUTYL 2255 excels in air Impermeability, is weather resistance, ozone resistance, heat resistance, and aging resistance. The heat aging resistance is improved for chlorobutyl and bromobutyl in comparison with regular butyl rubber.

Sylvin™ 7833-95 Yellow 4185 is a vinyl compound formulated for electrical molding applications.

Sylvin™ 7841-75 Black is a vinyl compound formulated for electrical molding applications.

Sylvin Technologies Sylvin™ 9684-85 Clear is a vinyl compound formulated with a non ortho phthalate plasticizer for clear electrical molding applications. This compound has an underwriters laboratories listing as a recognized component.

Sylvin Technologies Sylvin™ 9604A-95 Black is a vinyl compound formulated with a non ortho phthalate plasticizer for applications that require an alternative to DOP/DEHP plasticizer. This compound is suitable for extrusion or injection molding applications.

Shandong Xuye New Materials CPE135C has medium degree of crystalline and good melting fluidity. It is widely used in ABS, PE, PP and other plastic injection molding products to improve the flame retardant performance and increase compatibility.

GREENSTAB® 5885(PF) is used by PVC Pipe Manufacturers,PVC Accessories Manufacturers,PVC Cable Manufacturers.

Sylvin™ 9067-85LMW Gray 9269 is a vinyl compound formulated for injection molding applications. This compound has a underwriters laboratories listing as a recognized component.

Universal Colorant Company PVC Cable Masterbatch is the best filler for use in food grade and medical grade plastic industry. All these types of masterbatches are offered in different varieties of sizes, colors and shades. PVC masterbatches is best known for its quick dispersibility, lower dosage, migration resistance, weather resistance and non- blooming properties. These are suitable to use in rigid and foam PVC products including cables and profiles.

ANTI-OXIDANT 01(SV 91A001AO) is used for LDPE, LLDPE, HDPE & HDPE Telecommunication duct and it having advantage to Protect the polymer from degradation.

Ekflex 1081 is a general-purpose, non-phthalate plasticizer based on dioctyl cyclohexanoate (DOCH), featuring high performance and versatility in applications and designed to meet the most varied of domestic and international market needs and requirements in PVC and plastisol compound formulations. Delivering excellent performance, this plasticizer is a direct alternative for replacing phthalate plasticizes.

Black Masterbatch 4420 is recommended for injections, Blow moldings, Cables, Sheets, Pipes, Water Pipes, Fibers and Compound.

Sylvin™ 9067-90 Yellow 405 is a vinyl compound formulated for injection molding applications. This compound has a underwriters laboratories listing as a recognized component.

Sylvin™ 7833-75 Gray 9471 is a vinyl compound formulated for electrical molding applications.

Sylvin™ 7833-90 Yellow 4138 is a vinyl compound formulated for electrical molding applications.

Pratham Stearchem Sodium Stearate is the sodium salt of stearic acid. This white solid is the most common soap. It is found in many types of solid deodorants, rubbers, latex paints, and inks. It is also a component of some food additives and food flavorings. Sodium stearate comprises of a long hydrocarbon 'tail' and a carboxylic acid 'head' group. Of the two parts, the tail part has affinity for oils and head part has affinity for water.. The tail is basically an alkane, and so readily dissolves in fat, oil and grease, but not in water. The head-group however is polar, and so easily dissolves in water (hydrophilic - water-loving) and will not dissolve in oil or grease. Hence during any cleaning operation such as Dish Washing, Bathing or Laundry etc, the tail attaches itself to the oil droplets, and removes them from the dirty objects (dishes, clothes or body) collects together into clumps and washes down the drain.

PEROXAN PK295 GS is 1,1-Di-(tert.-butylperoxy)-3,3,5-trimethylcyclohexane 40%, Granules with chalk.PEROXAN PK295 GS is used for the crosslinking of natural rubber and synthetic rubber, as well as polyolefins.

Vatan Plastik San. Tic. AS V150 is a phthalate-free plastifian, which we produce in our chemical factory with the latest technology, has been used by cable, artificial leather, granule, hose, membrane filter and similar PVC manufacturers. The superior wetting property of the product can be observed especially in the productions where less plasticizer is used such as skin layers.

Sylvin™ 9077-90 White 1311 is a vinyl compound formulated for injection molding applications. This compound has a underwriters laboratories listing as a recognized component.

EVERNOX-1330 is used in polyolefins e.g. polyethylene, polypropylene, polybutene for the stabilization of pipes, molded articles, wires and cables, dielectric films etc. Furthermore, it is applied in other polymers such as engineering plastics like linear polyesters, polyamides, and styrene homo- and copolymers. It may also be used in PVC, polyurethanes, elastomers, adhesives, and other organic substrates. EVERNOX-1330 can be combined with other additives such as costabilizer (e.g. thioesters, phosphites, phosphonites), light stabilizer and other functional stabilizers. The synergistic blends of EVERNOX-1330 with EVERFOS-168 are extreme performance in polymers stabilization.

Jordan Mineral Est JM5C is a surface coated ultrafine ground calcium carbonate powder with excellent dispersion produced from microcrystalline rhombohedral high purity white limestone.

Microsphere® F-30 is chlorinated grade and is low temperature expansive product.

Karpatnaftochim Polyethylene HXB5210H is a white granules of the same geometric shape. Sintering of granules is not allowed.

Nurcacit MTT PDR used as vulcanization accelerator for chloroprene rubber, Injection-molded and technical extruded articles, profiles, hoses, seals, mills (rollers), cable sheeting, conveyor-belts based on CR. Possesses good module, age-resistance and advantageous compression set. Nurcacit MTT dispersed perfectly in compounds based on polychloroprene. As a result of its relatively low melting point (about 60 to 70 C), the material usually melts down and disperses without any problems. Because Nurcacit MTT is a powerful accelerator, it is best to incorporate it at the end of the mixing process together with ZnO. Particularly in compounds with a high rubber content, high viscosity or containing large amounts of active carbon black, MTT should be incorporated into the otherwise finished compound while it is being preheated for conversion.