Products in Automotive: Polyurethane (unspecified)

MB 1100 is an Olive colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1100 is low density foam of approximately 10lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1100 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

Ebalta MG 703 / Z 400 is a 2-components polyurethane material, which is cured thermically and used for prototypes. The four mentioned formulations differ in being filled or non-filled and their mechanical properties. The B-components Z 400 (potlife 8-12 min.) and Z 460 (potlife 60-70 min.) are identical and can be mixed with each other to control the reactivity, e.g. potlife. These combinations of Z 400 and Z 460 comp. B can be made any way as long as the totally required quantity of comp. B is observed (for each system).

DI-PAK E-4888 & E-4889High performance, flexible potting systems designed to be in constant water immersion while maintaining electrical and physical properties. DI-PAK E-4888 & E-4889 were designed to meet Naval underwater applications.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

TEXALAN® 290A This product is safe and environmentally friendly, has excellent abrasion resistance, solvent resistance, good hand feeling, repeated benefits High utilization rate, high strength and excellent processing performance

This product is a polyurethane system. Mechanical data according to test pieces post-cured for 8 hrs. at 80°C. No heavy chemical and mechanical stress before 7 days after curing at room temperature (20-23°C).

MU-107A It has the following properties: flexibility, low stress, moisture resistance, stress release, and shock absorption.

MU-231B its Functions Low Stress, High Thermal Conductivity, Stress Release, Shock Absorption.

TUFFALLOY 4270 is a series of Liquid Molding Compounds with thermoplastic properties such as high impact, high heat distortion, and low viscosity. This unique chemistry developed by Hapco to meet today's market demands for prototype and low production parts needs.THE TUFFALLOY 4270 Series are available in (4) speeds.The user has the ability to use different speeds of TUFFALLOY 4270, typically using a slower speed initially and increasing to a fast set, 1 minute working life.PROCESSING: TUFFALLOY 4270 Series can be pressure cast, vacuum cast, or open cast. For best results, TUFFALLOY 4274/75 should be used with Hapco's metering/dispensing equipment, RAPIDFIL, MINI FIL, and RAPIDSHOT.

TUFFALLOY 4270 is a series of Liquid Molding Compounds with thermoplastic properties such as high impact, high heat distortion, and low viscosity. This unique chemistry developed by Hapco to meet today's market demands for prototype and low production parts needs.THE TUFFALLOY 4270 Series are available in (4) speeds.The user has the ability to use different speeds of TUFFALLOY 4270, typically using a slower speed initially and increasing to a fast set, 1 minute working life.PROCESSING: TUFFALLOY 4270 Series can be pressure cast, vacuum cast, or open cast. For best results, TUFFALLOY 4274/75 should be used with Hapco's metering/dispensing equipment, RAPIDFIL, MINI FIL, and RAPIDSHOT.

TEXALAN® 285A This product is safe and environmentally friendly, has excellent abrasion resistance, solvent resistance, good hand feel, repeated benefits High utilization rate, high strength and excellent processing performance

MU-209A Its functions are flexible, low stress, stress release, and shock absorption.

DI-PAK E-4701, E-4951 and E-4501Easily pourable, thermally conductive, shock resistant potting compounds that are ideally suited for low and high production applications. This series of DI-PAK products reduce rejects by exhibiting extremely low stress on potted components. All three of the above DI-PAK E products are flame retardant and meet UL 94V-0 requirements.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

TEXALAN® 295A This product is safe and environmentally friendly, has excellent abrasion resistance, solvent resistance, good hand feeling, repeated benefits High utilization rate, high strength and excellent processing performance.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

DI-PAK E-4500 SERIESFlexible, 45, 65 and, 95 shore A hardness, potting and encapsulating systems. Flame retardant (FR), accelerated 3 minute (-3) gel time, and black or unpigmented versions are available.

DI-PAK E-4901-2, E-4901-10, & E-4901-30Low cost, easy to use, potting compounds with fast cycle times. Available in 3 speeds.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

RIGIDDI-PAK R-4525 SeriesA general purpose series of low viscosity, strong, potting and encapsulating compounds. DI-PAK R-4525 has excellent electrical insulating properties and bonds well to many substrates. By varying the curing agents, the desired cure and working life can be obtained.

The MU-120A performs the following functions: flexibility, low stress, heat resistance, stress release, and shock absorption.

RIGIDDI-PAK R-4545 SeriesA very low viscosity potting and encapsulating system with excellent flow and penetration into the most intricate electronic components, without voids or porosity. The R-4545 Series cure to a hard, shiny, high gloss, plastic finish that is free from "blushing" under all humidity conditions. The R-4545 Series is ideal for electrical applications where surface finish and appearance are critical.

RIGIDDI-PAK R-4545 SeriesA very low viscosity potting and encapsulating system with excellent flow and penetration into the most intricate electronic components, without voids or porosity. The R-4545 Series cure to a hard, shiny, high gloss, plastic finish that is free from "blushing" under all humidity conditions. The R-4545 Series is ideal for electrical applications where surface finish and appearance are critical.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

Polyurethane (PUR). Unfilled. Very good noise reduction. Good impact resistance even at low temperature.

Ultraclear™ 480N-20 by Hapco Inc. is comprised of Polyurethane (unspecified). It is commonly used as Casting Resin for a variety of applications.

DI-PAK E-4600 SERIESFlexible, high strength, 50 to 71 shore D hardness potting and encapsulating systems. Available in flame retardant (FR), 3 minute (-3) gel time, and in black or unpigmented.

TEXALAN® 298A This product is safe and environmentally friendly, has excellent abrasion resistance, solvent resistance, good hand feeling, repeated benefits High utilization rate, high strength and excellent processing performance.

RIGIDDI-PAK R-4528 SeriesA black, flame retardant, thermally conductive, high performance series that can be used in all types of electrical components. Combined with its ability to dissipate heat, DI-PAK R-4528 also provides low linear thermal expansion, low shrinkage, and low exothermic heat while curing. Meets UL requirements.

CarbonResin™ RPU 60 is a tough, abrasion-resistant material that is a good choice for parts that require rigidity, strength, and durability. Rigid Polyurethane is our most versatile rigid material family. It is used across a wide range of industries, including consumer products, automotive, and industrial. RPU is comparable to ABS.

Texalan® 380A This product has excellent wear resistance, oil/solvent resistance, low temperature flexural resistance, high pressure resistance, and Flexibility.

DI-PAK E-4501 Easily pourable, thermally conductive, shock resistant potting compounds that are ideally suited for low and high production applications. This series of DI-PAK products reduce rejects by exhibiting extremely low stress on potted components. All three of the above DI-PAK E products are flame retardant and meet UL 94V-0 requirements.

PolyWeb has superior capacity and performance with high open area up to 45 percent and reduced operating and maintenance costs from long life and ease of installation.

MB 1150 is an Avocado colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1150 is low density foam of approximately 15lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1150 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

ebalta MG 321 FR is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryllacquer- systems. As release agent you can use our T 03-01. MG 321 FR beige fire behavior according to UL 94, 3 mm thickness V0 With MG 883 the potlife of MG 321 FR beige can be set up to 120 secs. MG 321 FR-S beige/ black - Approved according to UL 94 - File E191776 Vol. 1 fire behavior based on UL 94, 3 mm thickness V0 and 5VA

Texalan® 360A product has excellent processing properties, oil/solvent resistance, low temperature flexural resistance, high resilience, and flexibility.