Products in Paints & Coatings: Trowel

Domacryl 9948 is a reactive 2-pack methacrylate resin, hardened with dibenzoyl peroxide designed for flooring. The resin is suitable for mortar, self-leveling, smooth and broadcasted floor coatings. Features and BenefitsFlexible base coat for flooring systemsVery fast curing even at low temperaturesLow VOCApplication with trowels or rollers.

KEMPERDUR® TC Traffic Coating is a high performance, odor-free, self-leveling, mineral-filled pedestrian and vehicular traffic coating for use with surfacing sand or ceramaquartz aggregate to provide a heavy-duty traction-enhanced surfacing. Concrete Substrate applications only.

CIM® 1061 is a tough, abrasion, corrosion and chemical resistant, liquid applied coating specifically for use in water and wastewater applications including those which require ANSI/NSF 61 potable water certification. Typical applications for this two component elastomeric urethane coating include tank and reservoir liners, joint seals, tank repairs, and chemical containment.

Armorcoat 969 Secondary Containment Coating Epoxy Floor Topping is a 100% epoxy, chemical and wear resistant topping for concrete, wood and steel. Armorcoat 969 is a two-part liquid system to which sand or inert granules are added. The surface texture depends on the type and amount of the granules used. Thickness of the AC 969 is approximately 1/8″ to 1/4″. Armorcoat 969 can be successfully used to:; Top surfaces such as trenches, warehouse floors and storage tank steps Patch tank containment areas and chemical loading pads Repair spalled concrete warehouses, industrial walk ways and irregular surfaces.

PREP COAT NCP, Non-cementitious Prep Coat, is formulated with a 100% styrene acrylic emulsion. It is a trowelapplied high performance coating for use as an optional base coat on the DuROCK PUCCS RMC and InsulROCK RMC Systems, as well as the DuROCK Exterior Finish Systems. NCP is a factory-mixed base coat that does not require the addition of water or Portland cement. NCP is normally used only as a base coat on combustible construction. However, on existing EIFS installations where it may be necessary to re-finish the system, NCP is recommended for skimming over-top of existing EIFS finish coats to level the surface prior to application of a new DuROCK Finish. NCP is a flexible and durable base coat that has greater flexibility than polymer based cement base coats, hence, it is ideal for areas where greater flexibility may be required. When used as a skim coat, it is intended to be applied very tight.

UREA-TUFF 4260 is a two-component, liquid-applied hybrid polyurea elastomer designed for use as a mix-in-the-bucket, but yet rapid-curing, monolithic waterproofing membrane. is a solvent-free aromatic polyurea-polyurethane elastomer containing no tar or asphaltic extenders.

L&L #300 Mastic UL Classified is a high-build, waterborne, elastomeric barrier coating. Its unique blend of premium acrylic resins and pigments combine to form a durable, mildew-resistant film with exceptional adhesion and flexibility. L&L 300 is a breathing mastic which allows damaging substrate moisture to escape, while protecting against ultra-violet, water and air-flow intrusion.

Warren Paint & Color 100% Solids Clear Epoxy Two Component #E15712/E15713 is formulated to provide extreme resistance to water, alcohol, and other chemicals. It may be used in aggressive environments for long-term protection of steel and concrete. 100% Solids Clear Epoxy is well suited for decoupage on bar tops, table tops, or as a clear finish over other interior wood and concrete surfaces. It may be applied up to 1/4" per pour for a coating with tremendous "depth." 100% Solids Clear Epoxy should not be used as an exterior topcoat.

Childers® CHIL-SPRED™ CP-135-2 is a water-based, combination protective coating and lagging adhesive that is non-flammable in the wet state and fire-resistive when dry. It is specially formulated for use with all lagging fabrics and insulations. When used as a coating, it forms a strong, tough and durable film, which protects the underlying insulation. When used as a lagging adhesive, it creates a strong bond to hold the laps of the lagging fabrics together.

Minchem NE50 is high-performance epoxy-based acid-resistant material designed to provide maximum resistance to aggressive chemical environments. It is typically provided in a two-component format comprising, an epoxy solution and an epoxy-based hardener, with the option of an inert filler powder with varying granulometry to suit the required thickness and application.

749 Vapor-Blok™ Water Based Elastomeric is a premium quality water-based vapor-barrier coating which effectively prevents water vapor from passing through it. It is designed to prevent the passage of water vapor into thermal insulation on cold systems or surfaces colder than ambient temperature. It is compatible with virtually all types of thermal insulation including Foamglas and can also be applied to a variety of other types of substrates as needed. It is a safe, easy-to-apply water-based latex emulsion, but it achieves the type of low perm rating normally associated with solvent-based products.

Duromar® DF-1301 is a clear, 100% solids concrete sealer with excellent flexibility and moderate chemical resistance. It is used primarily to seal the concrete prior to the application of additional topcoats, to prevent outgassing, and to restore the mechanical properties of old concrete. It can be cured at temperatures as low as 50ºF. Duromar® DF-1301 is a multifunctional epoxy with a uniquely modified cycloaliphatic amine hardener.

PERMATEC 3000 CT is a 100% solids epoxy floor topping designed for cool temperature applications commonly found in food and beverage processing facilities. The PERMA TEC 3000 CT system consists of a two component resin binder and graded aggregate. It is applied with a trowel or screed rake at 1/8 -1/4 inches (125 - 250 mils) in a one coat application (Cold Temperature) including a silica broadcast. There is no need for a primer or sealer coat. An optional glaze coat may be used to improve the appearance and cleanability. The vertical formulation of PERMA TEC 3000 CT is trowel applied at 1/8 inches (125 mils).

L&L 300 RCM Mastic is a high-solids, waterborne, elastomeric coating. Its high permeability coupled with optimum brightness greatly reduces the occurrence of polyurethane foam blisters (delamination) which frequently develop when existing polyurethane foam has been compromised by water intrusion, then re-coated. L&L 300 RCM Mastic is engineered to allow entrapped moisture vapor to escape through its membrane. Its bright white reflective surface reduces surface temperature, and in turn, minimizes vapor drive. While L&L 300 RCM Mastic has many other uses, it was designed specifically for re-coating existing polyurethane roof decks.

PERMATEC 4000 is a 100% solids, modified epoxy floor topping. The PERMATEC 4000 system consists of a two component resin binder and graded aggregate. It is applied with a trowel or screed rake at 1/8 -1/4 inches (125 - 250 mils) in a one coat application including a silica broadcast. There is no need for a primer or sealer coat. An optional glaze coat may be used to improve the appearance and cleanability. The vertical formulation of PERMATEC 4000 is trowel applied at 1/8 inches (125 mils).

DURAPATCH 3000D is an all purpose, quick cure epoxy paste kit. DURAPATCH 3000D is a unique, multi-component, novolac epoxy designed to quickly and permanently patch, seal and repair cracks, holes and leaks in metal, plastic, fiberglass and concrete surfaces. DURAPATCH 3000D cures in minutes, so down time is greatly reduced. DURAPATCH 3000D is perfect for machine shop and field use to repair and rebuild equipment. DURAPATCH 3000D is ideal for repairing warehouse floors, fixing leaks in tanks, repairing pool equipment and tiles, piping, electrical bushings, and setting keyways or taper fits for fast turnarounds. DURAPATCH is versatile, quick, easy to use, extremely strong and durable.

True-Bond CT™ is the answer for expansion joints or asphalt surfaces. From hairline cracks to crater-like potholes this product comes through every time. With up to 35% elasticity it is extremely flexible to temperature changes, yet incredibly hard and durable. Serves as an excellent waterproofing membrane for bridges and concrete overlays. Perfect for expansion joints, roof repairs and bridge footings, True-Bond CT™ boasts a minimum tensile elongation of 35%. True-Bond CT™ is asphalt filler and bonder that will not separate from bituminous surfaces. Repairs blacktop and concrete. Resists wear, corrosives, weather, impact. Waterproofing membrane for bridges and concrete overlays Bonds expansion joints and bridge footings. One application lasts for years.

Ever-Thane® Roof Flash is a high viscous, trowel or butter grade enhanced polyurea-urethane formula that can be used in conjunction with a variety of liquid coatings and a variety of roof membranes. It is designed to create a watertight liquid flashing for intricate roofing areas and details. With its low VOC’s, the single-component, moisture-cured liquid flashing is environmentally friendly. This high performing polyurea-urethane is durable, reflective and UV resistant and has excellent vertical hang and performs well under ponding water.

GacoFlex® LM60 is a 100% solids liquid applied two-component coating that cures into a water-resistant polyurethane elastomeric membrane. LM60H is designed for application on horizontal and low slope surfaces, at the rate of at least four gallons per 100 ft², to yield a 1/16" thick membrane. LM60V is designed for the same application rate and the yield on vertical surfaces.

CIM® 1000 is a liquid applied urethane coating that cures in hours to form a tough elastomeric coating that adheres to most substrates, forming a chemical and abrasion resistant barrier for waterproofing, corrosion protection, and containment of water and most aqueous chemicals.

GacoFlex® LM-60AR is a 100% solids liquid applied two-component coating that cures into a water-resistant polyurethane elastomeric membrane. LM-60HAR is designed for application on horizontal and low slope surfaces, at the rate of at least four gallons per 100 ft², to yield a 1/16" thick membrane. LM-60VAR is designed for the same application rate and the yield on vertical surfaces.

Duromar® HydroFlor® is an innovative, zero VOC epoxy floor coating. It has a unique breathable structure, which allows moisture vapor to escape from the concrete. The coating is easy to apply. Duromar® HydroFlor® has a matte, anti-slip finish. It is recommended to first apply HydroFlor® Sealer to prevent outgassing during application. Duromar® HydroFlor® is a multifunctional epoxy, with a uniquely modified amine hardener.

Thermaguard™ TIC 400 is a new technology waterbased, single component, inorganic polymeric siloxane matrix, Thermal Insulation Coating (TIC). The insulation coating is formulated to provide a seamless, hydrophobic, weather resistant insulation film. The insulation coating is an inorganic & ultra-low VOC coating. Offering hydrophobicity (moisture resistance), operating temperatures from -60 to 400oC range & exceptional weathering resistance. Thermaguard™ TIC 400 acts as a thermal barrier, which can improve energy efficiency, prevent Corrosion Under Insulation (CUI) occurring, reduce condensation build up & provide personal protection according to ISO 13732-1 (SafeTouch™ properties). Protecting interior temperatures against cold, warm & humid weather conditions. Elimination of external cladding results in a maintenance friendly insulation system for quick inspections. Thermaguard™ TIC 400 has Ultra-High-Build (UHB) capabilities up to 20000 microns DFT in a single multi-pass application. Application at such thicknesses allows use of Thermaguard™ TIC 400 liquid insulation to partly or completely replace use of traditional insulation material systems.

Design Polymerics 5060 Low Viscosity Water Based Weather Barrier Coating is water based, high strength, premium quality, low odor, low VOC, quick drying weather barrier/weatherproofing coating. 5060 Low Viscosity Water Based Weather Barrier Coating is a bright white color and has excellent brush properties.

Skim-kote is a polymer modified cement base coat and surface leveler.

RC 1650 Acrylic Seam Compound is a high quality, high solids, acrylic elastomeric seam sealer designed to bridge and seal seams, gutters, vent pipe flashings, air conditioning units and expansion joints for all types of roofing substrates. RC 1650 has excellent weatherability and ultraviolet resistance. RC 1650 also offers a flexible, durable sealer with excellent resistance to mechanical or chemical attacks.

VF 30™ is a low viscosity, high solids epoxy developed as a penetrating concrete primer for polyurea applications. VF 30 penetrates and strengthens the surface of the concrete, reduces pin-hole formations and provides a chemically reactive surface to accept VersaFlex polyurea systems. Adhesion is increased with the use of VF 30 by up to three times that of unprimed concrete.

PREP COAT PLUS is 100% styrene acrylic emulsion that is field-mixed with Portland cement. It is a trowel-applied high performance coating for use on DuROCK PUCCS RMC and InsulROCK RMC Systems as a base coat and adhesive with enhanced flexibility and strength. Prep Coat Plus is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, and breathable to water vapor. Prep Coat Plus can be applied as a high-build leveling coat, for added impact resistance on EIFS or to make a wall plumb and flat, applied up to 6.4 mm (¼ inch) thick in a single pass if required.

Minchem NEGF30 is high-performance epoxy-based acid-resistant material designed to provide maximum resistance to aggressive chemical environments. It is typically provided in a two-component format comprising, an epoxy solution and an epoxy-based hardener, with the option of an inert filler powder with varying granulometry to suit the required thickness and application.

Tique Ground Coat is an elastomeric weather resistive air barrier, adhesive and base coat combined with Portland Cement. Tique Ground Coat is used in the Tique Continuous Insulation Systems, as well as in the direct applied application on vertical wall assemblies. It is a two component product.

PREP COAT Q is a fast drying, dry polymer based dry-mix material that is field-mixed with water. It is ideal for use in cold temperature, high humidity conditions. It is a trowel-applied high performance coating for use on DuROCK PUCCS and InsulROCK Systems as a non-combustible base coat and adhesive. Prep Coat Q is a flexible and durable base coat that can also be used as a leveling coat for stucco, concrete and masonry substrates. It has excellent freeze-thaw stability, low water absorption, breathable to water vapor and non-combustible. It is a convenient product since it requires only water to be added on site.

SunShield solar protective coating is a premium quality, highly pigmented, polymeric surfacing system designed for heat reduction of parking surfaces. The product is formulated with infrared refl ective pigments to reduce solar absorptance, increase reflectance and achieve the desired solar reflectance index (SRI). SunShield binds specifically graded subangular aggregate for non-slip performance and to achieve a diffuse reflective surface. SunShield contains no PAHs and has an extremely low VOC content.

Minchem VEGF30 is a high-performance vinyl ester-based acid-resistant material designed to provide maximum resistance to aggressive chemical environments. It is typically provided in a two-component format comprising, a vinyl ester solution and a catalyzed filler powder, which can be altered, with varying granulometry to suit the required thickness and application.

CIM® 800 is a tough, weather durable, waterproofing coating specifically formulated to meet the demands of waterproofing above or below grade. This two component, cold, liquid applied urethane coating adheres to most materials to form a permanent seamless barrier to water. It is especially well suited for roofs over critical spaces (e.g. clean rooms, control rooms), green roofs, plaza decks, areas with multiple penetrations and curbs, and between-slab waterproofing.

PERMATEC 4000 HT is a 100% solids epoxy floor topping designed for high temperature applications commonly found in many manufacturing processes. PERMATEC 4000 HT is designed to withstand constant temperatures to 212°F (100°C) and intermittent exposures to 250°F (122°C). The PERMATEC 4000 HT system consists of a two component resin binder and graded aggregate. It is applied with a trowel or screed rake at 1/8 -1/4 inches (125-250 mils) in a one coat application including a silica broadcast. There is no need for a primer or sealer coat. An optional glaze coat may be used to improve the appearance and cleanability. Where chemical exposures over 150°F are anticipated, contact ChemProof Polymers for specific recommendations. The vertical formulation of PERMATEC 4000 is trowel applied at 1/8 inches (125 mils).

CHEM-NOVOLAC is a two-component, solvent-free, 100% sol epoxy system which exhibits superior resistance to acids, b mineral and organic, alkalis, salts, solvents, oils and ot chemicals. CHEM-NOVOLAC is high gloss, abrasion resist and moisture insensitive. Coatings and toppings of CHE NOVOLAC have excellent resistance to thermal shock w subjected to frequent steam or hot water cleaning.