Products in Other Industrial Applications: Wear Resistant

InnoMid® PA6.9 M0105000000660 is a Polyamide 66 that has wear resistant, heat Stabilized and is available in Natural color.

PBT-GF30, PBT, 30% glass fiber reinforced, approved for use in food contact

Comco PA6C Natural is a universal material for general structural parts in plant and mechanical engineering. PA6C has very good antifriction properties and good resistance to gamma and X-rays.

AF801 Peek™ 450G are used in a wide range of oil and gas applications due to the unique combination of properties and range of compounds and unfilled polymers.

POM copolymer unreinforced, low viscosity, laser-inscribable

Techno Compound PBT4 Natural (9999) is a thermoplastic which combines great hardness, stiffness and strength. TechnoDur is easily processed due to its perfect flow behavior. The favorable sliding and wear characteristics as well as extremely high tenacity in temperatures below freezing are further advantages.

Comco PEEK is available in plates, rods, blanks cut to size and machined parts according to the customer’s drawing. Our standard colors: natural and black. Various colors such as blue and red can be produced according to the customer’s requirements.

Enflon® 101 is 5% glass fiber. Milled glass fibers have the least effect on chemical and electrical properties and add greatly to the mechanical properties of unfilled PTFE. The addition of glass improves compressive properties by as much as 40% and improves wear resistance greatly. These compounds resist acids and oxidation, but can be attacked by alkalis.

Nilit NILAMID® A3 GF50 TM2 is a Polyamide 66 (Nylon 66) compound, 50% glass fiber reinforced, low wear and friction with molybdenum disulphide.This compound is intended for injection molding.NILAMID® A3 GF50 TM2 is primarily designed for the Industrial and Consumer industry. It is also suitable for Electrical and Electronic or Automotive applications.

This material is ideally suited for use in the food sector and medical industry. As a fluorinated plastic, Murinyl® is exceptionally resistant to chemicals, hydrolysis, and sterilization. Moreover, the properties of the material change very little even at high service temperatures and after long-term exposure to UV radiation, meaning that Murinyl® is ideally suited for a wealth of applications both inside and outside. Production based on PVDF.

BARLOG plastics GmbH Kebablend® / WR 01/2420 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material has medium strength and a high elongation at break.

Yi Mei New Material Technology FT-Wax-F70 is a methylene polymer, which is an alkane polymer synthesized from hydrocarbon syngas or natural gas. It mainly relies on high quality and cheap raw materials of coal chemical industry for iron-based or cobalt-based synthes is, which has obvious advantages over crude oil wax price.

Enflon® 110 is 5% graphite. Graphite offers improved chemical resistance to corrosive environments and exhibits good initial wear and rubbing/sliding characteristics in dry and water applications. Graphite is commonly blended with carbon and PTFE.

Nylacast PA 6 Natural is the basic PA 6 grade from which all the other grades of cast nylon stem. Generally accepted as the primary engineering polymer, natural cast nylon is suitable for virtually any plain bearing application, not to mention a huge range of other applications for which this versatile grade finds a use. By varying the conditions of polymerisation the mechanical properties of cast nylon may be altered to suit specific applications and the performance of the basic polymer can be enhanced with the addition of various additives, fillers, lubricants and colorants (see further grades). Compared with injection molding and extrusion grades of polyamide, cast nylons stand out with their improved mechanical, thermal and chemical resistance properties.

Grupa Azoty S.A Tarflen® SM-B30 is a Polytetrafluoroethylene (PTFE) material filled with 30% bronze. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America.Important attributes of Tarflen® SM-B30 are: Chemical Resistant Flame Retardant Wear Resistant Weather Resistant Typical applications include: Engineering/Industrial Parts Coating Applications Hose/Tubing Plumbing/Piping/Potable Water Sealing Applications

Polimersan Plastics Politef ( P.T.F.E. ) is highly resistant to chemical liquids and solvents.

PBT-GF50, PBT, 50% glass fiber reinforced, approved for use in food contact

Nylene Duratel MF3 is a high-viscosity acetal co-polymer. Duratel MF3 has slightly higher toughness than standard MF9, and parts molded with MF3 should have thicker wall sections and shorter flow lengths to accommodate the higher viscosity. MF3 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Twaron® short-cut fiber can raise the performance of a wide range of products, including rubber compounds and engineered plastics.

Sylvin™ 9470-88 Black is a pvc/tpu alloy formulated to improve abrasion and wear resistance for injection molding applications.

PAR Group Nylon 6 MoS2 Extruded Sheet offers increased load bearing and wear resistance, whilst maintaining the impact and fatigue resistance of standard nylon grades. It is self-lubricating, electrically insulating and has a high fatigue resistance. We also manufacture our own brand of Corromide® CMF (Nylon 6 Sheet - MoS2 Filled Cast) in sheets, rods and tubes. Our MoS2 Filled Cast Nylon 6 is available in greater sheet thicknesses and offers a higher temperature rating compared to MoS2 Filled Extruded Nylon 6. Nylon 6 Sheet - MoS2 Filled Extruded is available to buy online at PAR Direct by clicking the link above.

BARLOG plastics GmbH Kebaform® / C 25 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Kebaform® / C 25 H improves the sliding and wear behavior solely by modifying the polymer chain and there is no reduction in mechanical properties due to the addition of tribologically active additives. Due to its property profile, Kebaform® / C 25 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

Enflon® 166 is maroon in color, this material provides high wear resistance and low friction in a continuous, non-lubricated service. Good dielectric and insulation properties. Excellent choice for bearings, gaskets and high pressure applications requiring robust components. Alternative to Rulon® LR.

Yi Mei New Material Technology FT-Wax-F52 is a methylene polymer, which is an alkane polymer synthesized from hydrocarbon syngas or natural gas. It mainly relies on high quality and cheap raw materials of coal chemical industry for iron-based or cobalt-based synthes is, which has obvious advantages over crude oil wax price.

Nylene Recommended for molding applications requiring both maximum durability and toughness Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

Smooth blend-POM-1200 is a weer resistant polyacetal compound offering superb lubricity by incorporating PTFE. It is developed for application demanding stringent wear resistant and low friction performance.

Chengdu Letian Plastics LTP ZW-3100 has high strength and low density and is broadly applied as wear resisting parts under elevated temperature and humidity work conditions for aerospace, automotive, machine, household appliances, petroleum and chemical industry, such as bearing, axile bush, gear wheel, impeller blade, belt roller, brake block and so on.

Twaron® powder allows manufacturers to easily and quickly raise product performance standards and add considerable value. Twaron® powder is available in different forms and particle sizes.

Glass filled PEKTRON PEEK 1030 has increased strength, good creep resistance, and is not conductive.

Flontech PTFE FT-GL25-1 contains features such as thermal expansion 10% greater than that of metallic materials, low abrasion resistance, starting from a certain load level it becomes permanently deformed due to cold flow, low thermal and electrical conductivity.

POM-I, POM copolymer unreinforced, medium viscosity, impact modified

Nylene Low wear 30% glass fiber reinforced nylon 6/6 Provides a low friction and low wear surface while maintaining the high strength and stiffness required from a glass fiber reinforced - Suitable for applications such as bushings and bearings, wear plates, caterpillar tracks, and other parts where wear may be an issue

Impact-modified, heat-stabilized, nylon 6/6 molding resin with high impact strength Free of silicones, it possesses very low wear properties

Techno Compound PBT4 GF 30 Natural (9987) is a thermoplastic which combines great hardness, stiffness and strength. TechnoDur is easily processed due to its perfect flow behavior. The favorable sliding and wear characteristics as well as extremely high tenacity in temperatures below freezing are further advantages.

LiNNOTAM with oil finely distributed in the material. LiNNOTAMGLiDE has the added Lubricant self-lubricating properties and has excellent wear resistance low coefficient of friction.

Antero™ 800NA is a PEKK-based FDM® thermoplastic. It combines FDM’s design freedom and ease of use with the excellent strength, toughness and wear-resistant properties of PEKK material. Antero 800NA exhibits high heat resistance, chemical resistance, low outgassing and dimensional stability, particularly in large parts. Appropriate applications include aircraft components exposed to jet fuel, oil and hydraulic fluid, spacecraft parts that demand low outgassing and chemical-resistant industrial parts. Using Antero 800NA with FDM technology avoids the waste associated with subtractive manufacturing of high-cost bulk PEKK material. Antero 800NA is available on Fortus 450mc™ and F900™ 3D Printers and is compatible with breakaway support material SUP8000B™.