Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Application Method
- Coverage
Varies upon substrate: approximately 160 - 200 ft² per gal., per coat (14.9 - 18.6 m² per 3.8 L, per coat) 8 - 10 mils wet; 2.4 - 3 mils cured
- Suitability Sample
- Due to condition specific sites, always prepare an adequate number of test areas.
- Wear protection system and esthetic suitability for products’ intended use should be included.
- On-site sample approval is especially critical on substantial, heavy traffic situation or custom coloration.
- Clean-Up
Before the product dries; spills and tools can be cleaned up with a solvent such as xylene or acetone.
- Limitations
- For use by trained professionals that have read the complete SDS.
- The product is strictly for interior use, upon a well-drained concrete slab with an appropriate vapor barrier, subject to no hydrostatic pressure.
- When masking use caution while taping to a floor that is not completely cured, especially at the edges, as delamination may occur.
- Protect from metal wheel traffic and some furniture where point of contact may be damaging.
- Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking
- Application Temperature
50 - 90 °F
Properties
- Appearance
- Color Satin (Cured), Color (Wet)
- Odor
- Solvent
- Chemical Properties
Value Units Test Method / Conditions Brake Fluid Remove Immediately - ASTM D-1308 Formula 409 Resistant - ASTM D-1308 Gasoline Remove Immediately - ASTM D-1308 Motor Oil Resistant - ASTM D-1308 Transmission Fluid Resistant - ASTM D-1308 - Typical Properties
Value Units Test Method / Conditions Abrasion Resistance 12.5 g Loss - Adhesion (Dry Concrete) Excellent - ASTM D-3359 Adhesion (Wet Concrete) Excellent - ASTM D-3359 Block Resistance Excellent - ASTM D-4946 Blush (18hr Immersion ) No Blush - - Blush (4hr Dry) No Blush - - Diluents Hydrocarbons - - Film Formation (40°F) Passed - - Heat Stability (120°F) Excellent - ASTM D-1849 Hot Tire Pick-Up* Passed - - Light Stability Excellent - - Mechanical Stability Excellent - - Pencil Hardness HB-H - ASTM D-3363 Solids 30.0 % - VOC Content 600.0 g/L - Water Absorption 2.4 g/m³ - Water Resistance Excellent, Beads Water - - - Hot Tire Pick-Up*
- Under extreme circumstances, delaminating could occur.
- All tire manufacturers were not tested.
- Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking.
Regulatory & Compliance
- Slip Resistance
- Two recognized US agencies have issued directives on minimum coefficient of friction, OSHA (Occupational Safety and Health Administration) and Department of Justice through the ADA (Americans with Disabilities Act).
- ADA is the more stringent of the two. ADA directs that accessible walkways have a minimum coefficient of friction of 0.6. Ramps have been directed to be 0.8.
- The applicator assumes the responsibility to meet these standards. Areas that may become wet, oily, or greasy require special attention.
Technical Details & Test Data
- Weather Testing
- QUV accelerated
- ASTM G-53
- No blistering, no yellowing
- 250hours
Safety & Health
- Caution
- Keep out of reach of children.
Inhalation:
- Avoid prolonged breathing of airborne dust, particularly present during mixing.
- Use NIOSH approved respirator for nuisance if threshold limit values are unsafe.
Skin Contact:
- Skin contact may cause irritation.
- Remove contaminated clothing and wash affected skin with soap and water.
- Launder clothing before reuse.
- If symptoms persist, seek medical attention.
Eyes:
- Wear safety eye protection when applying.
- Contact with eyes may cause irritation.
- Flush eyes with water for 15 minutes.
- If symptoms persist, seek medical attention.
Packaging & Availability
Storage & Handling
- Shelf Life
Under normal, moisture free conditions 12 months for unopened container.