Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Name
- INCI Name
- Ingredient Origin
- Agrochemical Functions
- Cleaning Ingredients Functions
- Cosmetic Ingredients Functions
- Industrial Additives Functions
- CAS No.
- 68891-38-3
- EC No.
- 500-234-8
- Technologies
- Product Families
- Chemical Structure
CH3 (CH2)10 CH2 (OCH2 CH2)2 OSO3 Na
Features & Benefits
- Benefit Claims
- Labeling Claims
- HII Features
- Features
Preservative Free
Applications & Uses
- Markets
- Applications
- Application Format
- Bath & Shower Applications
- Hair Care Applications
- Home Care Applications
- I&I Cleaning Applications
- Industrial Additives End Use
- Personal Hygiene Applications
- Skin Care Applications
- Applications
- STEOL CS-270 C provides improved mildness over sodium lauryl sulfate without sacrificing critical performance attributes, such as foaming and viscosity response. Its low irritation properties make it ideal for mild cleansing products.
- STEOL CS-270 C can be readily formulated into shampoos, bath products, hand soaps, and detergents offering the required physical properties and performance attributes.
- Products based on STEOL CS-270 C can be thickened with salts, betaines, or amides, with the latter two also serving to enrich the foam. A variety of performance and physical attributes can be obtained simply by adjusting the amount of additive incorporated into a formula. Since STEOL CS-270 C is compatible with commonly used opacifying and pearlizing agents, the formulator is afforded flexibility in developing the desired product appearance.
Properties
- Formulation Type
- Physical Form
- Appearance
- Mobile paste (at 25°C)
- Typical Properties
Value Units Test Method / Conditions Boiling Point min. 100 °C - Actives Content (MW 382) 68 - 72 % - Unsulfated Alcohol max. 2.5 % - Critical Micelle Concentration (CMC) 279 mg/L - Sodium Sulfate Content max. 1 % - pH (10% in aqueous solution) 7.0 - 9.0 - - Color (Transmittance at 440 nm, 25% active) min. 90 % - Flash Point min. 94 °C PMCC Flash Point Tester Sodium Chloride Content max. 0.5 % - Freeze Point 5 °C - Density (at 25°C) 1.03 g/ml - Regulated Volatile Organic Chemicals 0 % U.S. EPA
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
- Clearances
- All components of STEOL CS-270 C are listed in the following countries: United States (TSCA 68585-34-2), Australia (AICS 68585-34-2), Canada (DSL 68585-34-2), China (IECSC 68585-34-2), Europe (NLP 500-223-8), Japan (ENCS 2-1682), Korea (ECL Serial No. KE-32438), Philippines (PICCS 68585-34-2) and New Zealand (ZNloC 68585-34-2). It is the responsibility of the end user to review the chemical control regulations for each country.
- STEOL CS-270 C meets the U.S. EPA Safe Choice Program’s surfactant screen.
Safety & Health
- Health Effects
Product is slightly to practically non-toxic orally (LD₅₀ >5 g/kg).and it causes minimal skin and moderate eye irritation at 10% active.
Packaging & Availability
Storage & Handling
- Workplace Exposure
Occupational exposure can occur primarily through skin contact or via inhalation of vapors and mists. Engineering controls, personal protective equipment, and other workplace practices should be used to control these exposures.
- Storage & Handling
- Normal safety precautions (i.e., gloves and safety goggles) should be employed when handling STEOL CS-270 C. Contact with the eyes and prolonged contact with the skin should be avoided. Wash thoroughly after handling material.
- The recommended dilution procedure for STEOL CS-270 C is to heat the precalculated water charge to 30-40 °C (86-104 °F). While agitating, add the STEOL CS-270 C at such a rate as to allow the product to dissolve without forming large gel masses. If excessive foam is generated, decrease agitation. All inorganic salts should be added once a clear solution of desired activity has been obtained.
- It is recommended that STEOL CS-270 C be stored in sealed containers and kept at temperatures between 32-43 °C (90-110 °F). Avoid overheating or freezing. If material is frozen, heat mildly using warm water tracing.
- Bulk Storage Information: Tanks, pumps, pipes and heat exchangers made of 316 stainless steel are recommended. Rotary piston type (positive displacement only) pumps are recommended. Recommended storage temperature for bulk tanks is 32-43 °C (90-110 °F).