Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Chemistry
- Polyether
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- 100% solids - no shrinkage
- Fast skin over - low dirt pickup
- Safe to Use - solvent & Isocyanate free
- Ultra-low VOC’s, 35.2 g/L
- May contribute to LEED V4 EQ Material Resource Credit 4.1 - Adhesives and Sealants
- Bonds to most common building substrates
- Remains flexible to absorb expansion and contraction
- High Performance Durability
- Does not dry or become brittle
- Water resistant
- Permanent elastomeric bond
Applications & Uses
- Markets
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Substrate Compatibility
- Aluminum
- Coated Metal
- Glass
- Wood
- EPS Foam
- Stainless Steel
- Cold Rolled Steel
- Concrete
- Block and Brick
- Ceramics
- Fiberglass
- Many plastics
- Ease of Installation
- Single component high solids formula.
- Easily gunnable between 40°F and 100°F.
- Cures rapidly to reach optimum strength within 7 - 14 days, optimum cure 21 days.
- SB MSL can be installed on damp surfaces which is defined as when no moisture is transferred to the skin when the substrate is touched.
- Product Application
Application
Remove all dirt, oil, loose paint, frost and other contamination from all working surfaces. Maintain SB MSL at room temperature before applying to ensure easy gunning and tooling. Test and evaluate to ensure adequate adhesion.
Concrete
Prior to application remove any residual contamination by mechanical abrasion, sand blasting or power washing. On green concrete, remove all release agents and loose concrete. Dry all visible and/or standing water. Install an appropriate backer rod to avoid three-point bonding.
Metal
Prepare all metal to ensure maximum adhesion. Remove all rust, scale and residue using a wire brush. Remove films, loose or inappropriate coatings and oils with an appropriate solvent such as alcohol. Seal Bond recommends that coated substrates be tested for proper adhesion prior to starting a project to determine suitability for use.
Wood
Wood should be clean, sound and dry prior to sealant application. Allow treated wood to weather for six months prior to application. Remove all coatings and paint to ensure proper adhesion. SB MSL is not recommended for use on fire retardant lumber.
Priming
n most applications SB MSL will not require a primer. However, certain substrates may require a primer to ensure a long lasting bond and weatherproof seal. It is the applicator’s responsibility to determine whether or not a primer is needed in their specific application.
Clean-up
Clean tools with mild solvent such as mineral spirits.
Properties
- Typical Properties
Value Units Test Method / Conditions VOC 35.2 g/L ASTM C1250 Skinover Time (50% RH, 70°F) 15.0 min ASTM C679 Density 13.69 lb/gal - Hardness 48.0 - ASTM D676 (Shore A) Peel Strength (Aluminum) 14.57 - ASTM D903 Peel Strength (Mortar) 14.33 - ASTM D903 Peel Strength (Glass) 14.33 pli ASTM D903 Peel Strength (Pine) 11.01 - ASTM D903 Peel Strength (PVC) 13.41 - ASTM D903 Peel Strength (Cold Rolled Steel) 12.09 - ASTM D903 Tensile 168.0 psi ASTM D412-06 Elongation at Break 184.0 % ASTM D412-06 Shrinkage 0.0 % - Service Temperature -40 to 200 °F - Viscosity (1 rpm) 80000.0 cps ASTM D2196-10 Viscosity (2 rpm) 63000.0 cps ASTM D2196-10 Viscosity (10 rpm) 45400.0 cps ASTM D2196-10
Regulatory & Compliance
- Certifications & Compliance
- Standards & Compliance
- May contribute to LEED V4 EQ Material Resource Credit 4.1 - Adhesives and Sealants
- ASTM C-920, Type S, Grade P, Class 25, use T, M, A, G and O
- Federal Specification TT-S-00230-C Type 1, Class A
- Corps of Engineers CRD-C-541, Type I, Class A
- Conforms to OTC Rule for Sealants and Caulks
- Meets requirements of California Regs: CARB, BAAQMD and SCAQMD
- Conforms to USDA Requirements for Non-food Contact
Technical Details & Test Data
- Test Data
SB MSL typical values represent data from multiple batches. Values will be refreshed, as necessary, upon data collection from additional campaigns and long-term variability discernment.
Safety & Health
- Precautionary Statements
- Do not use until all instructions and safety precautions have been read and understood.
- Wear protective gloves, protective clothing and eye protection.
- Wash contaminated clothing before reuse.
- Contaminated work clothing should not be allowed out of the workplace.
- If on skin - Wash exposed body areas with soap and water.
- If in eyes - Rinse with water, remove contact lenses and continue rinsing.
- If exposed or concerned get medical advise/attention.
Packaging & Availability
- Packaging & Availability
- 10.1 oz. (300 ml) cartridges - 24 tubes/case, 45 cases/pallet
- 2 liter pouches - 4 pouches/case, 40 cases/pallet
- Available in colors, white, black and gray.
Storage & Handling
- Material Storage and Disposal
- Store securely between 60°F - 80°F in unopened container.
- Recommended shelf life is 12 months from date of manufacture on bottom of tube.
- Keep tube tightly sealed.
- Dispose of contents/container in accordance with Local/Regional/National/International Regulations.
- Shelf Life
The shelf life is 12 months for an unopened container from the date of manufacture.