Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Composite Materials Functions
- Technologies
- Product Families
Features & Benefits
- Materials Features
- Features and Benefits
Features
- Iso-NPG base resin
- Easy to apply
- Exceptional chemical resistance
Benefits
- Heat resistant
- Can be polished to a high gloss
- Versatile
Applications & Uses
- Markets
- Applications
- Application Method
- Brush Application
Do Don’t Ensure the gelcoat has attained workshop temperature of 15°C - 25°C before use. Stir the gelcoat with high shear mixers as this will temporarily break down the thixotropy leading to drainage. Gently stir the gelcoat by hand or low shear stirrer, then allow to stand before use. Exceed a wet film thickness of 800 microns as thick films encourage air retention. Add 2% Butanox® M-50 or equivalent catalyst. Apply excessive thickness in corner areas as this can cause pre-release. Use long brush strokes and even pressure to apply the gelcoat in an even film across the mold surface. Apply backing laminate before the gelcoat has reached an appropriate degree of cure. Use thorough brushing action to build wet film thickness evenly to 600-800 microns. Catalyze more gelcoat than can be applied before it starts to gel. Apply the first layer of laminate within 24 hours of the gelcoat. Allow vapor to be retained in deep mold sections as this can cause slow curing. - Gel Time and Backup Time
- Catalyst level and initiation temperature will influence the gel time
- The product only requires the addition of catalyst to start curing as it is pre-accelerated. An exothermic reaction will take place.
- We recommend the use of a 50% MEKP (type Butanox M50 or equivalent) which should be added at 2% in the gelcoat
Temperature Gel time (2% Butanox M50)* Backup time (2% Butanox M50)* 25°C 7 - 12 minutes N/A *Measured under laboratory conditions. Information should be used as a guide only
Properties
- Cured Properties
Value Units Test Method / Conditions Barcol Hardness (Model GYZ 934-1) 46 - EN59 Water Absorption (24h, at 23°C) 17 mg BS EN ISO 62 part 6.2 Heat Deflection Temperature (1.8 MPa)† 83 °C BS EN ISO 75-2 (1996) Elongation (at break)* 2 % BS EN ISO 527-2 Tensile Strength* 64 MPa BS EN ISO 527-2 Tensile Modulus* 3800 MPa BS EN ISO 527-2 - Uncured Properties
Value Units Test Method / Conditions Viscosity (at 25°C, 0.6 s⁻¹) 300 - 500 Poise - Specific Gravity (at 25°C) 1.1 - - Styrene Content 34 % - - Note
*24 hours at workshop temperature followed by 3 hours at 80°C (Scott Bader post-cure)
† Heat deflection testing has an additional 3 hours at 120°C (Scott Bader post-cure)
Technical Details & Test Data
- Additives and Variants
- The information contained in this technical data sheet applies to all pigmented versions
- The topcoat can be formulated by addition of 2% Crystic® Solution MW into the gelcoat
- Incorporation of additional material may affect the working, weathering or cured properties of the gelcoat. Please check with Scott Bader’s Technical Service team before using the gelcoat outside of specified parameters
- Post Curing
- The post-cure schedule will affect the end-product properties.
- For optimum properties laminates must be post-cured before being put into service
- 24 hours at workshop temperature, followed by oven-cure for 16 hours at 40°C (Lloyds post-cure) L
- 24 hours at workshop temperature followed by 3 hours at 80°C (Scott Bader post-cure) *
- Heat deflection testing has an additional 3 hours at 120°C (Scott Bader post-cure) †
- Recommended Testing
It is recommended that customers test all gelcoats under application conditions prior to full-production to ensure that the product meets specification
Safety & Health
- Health and Safety Information
Unsaturated polyester products release heat when they cure in bulk.
Packaging & Availability
- Packaging Type
- Packaging Information
Crystic® 12PA is available in 25kg and 225kg and IBC containers.
Storage & Handling
- Shelf Life
- 5 Months
- Storage Conditions
- Crystic 12PA should be stored in its original container, under cover, and out of direct sunlight. These must be kept closed and airtight. It is recommended that the storage temperature should be less than 25oC and the product should not be frozen. Storing the product outside of these conditions may affect the properties of the product and reduce its shelf life. Ideally, containers should be opened only immediately prior to use.
- The product should be used within 5 months of the date of production.