Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Break, Type I, 5 mm/min) ¹¹ 114 MPa ASTM D638 Tensile Strain (Break, Type I, 5 mm/min) ¹¹ 2.5 % ASTM D638 Tensile Modulus (at 5 mm/min) ¹¹ 8690 MPa ASTM D638 Flexural Stress ¹¹ 180 MPa ASTM D790 Flexural Modulus ¹¹ 7410 MPa ASTM D790 Tensile Stress (Break, 5 mm/min) ¹¹ 115 MPa ISO 527 Tensile Strain (Break, 5 mm/min) ¹¹ 2.50E+00 % ISO 527 Tensile Modulus (at 1 mm/min) ¹¹ 8610 MPa ISO 527 Flexural Stress (Yield, at 2 mm/min) ¹¹ 172 MPa ISO 178 Flexural Stress (Break, 2 mm/min) ¹¹ 180 MPa ISO 178 Flexural Modulus (at 2 mm/min) ¹¹ 7450 MPa ISO 178 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.43 - ASTM D792 Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹ 0.1 - 0.4 % SABIC method Mold Shrinkage (xflow, 3.2 mm) ᵍ ¹¹ 0.2 - 0.5 % SABIC method Melt Volume Rate (at 300°C, 2.16 kg) ¹¹ 9 cm³/10 min ISO 1133 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ 125 °C ASTM D648 Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ 0.000021 1/°C ASTM E831 Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ 0.000068 1/°C ASTM E831 - Impact Properties
Value Units Test Method / Conditions Charpy Impact (Unnotched, at 23°C) ¹¹ 45 kJ/m² ISO 179/2C Izod Impact (Unnotched, at 23°C) ¹¹ 715 J/m ASTM D4812 Izod Impact (Notched, at 23°C) ¹¹ 165 J/m ASTM D256 Charpy Impact (Notched, at 23°C) ¹¹ 17 kJ/m² ISO 179/2C - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 90 - 110 °C - Drying Time ⁷ 3 - 5 Hrs - Melt Temperature ⁷ 280 - 320 °C - Nozzle Temperature ⁷ 280 - 320 °C - Front - Zone 3 Temperature ⁷ 280 - 320 °C - Middle - Zone 2 Temperature ⁷ 280 - 320 °C - Rear - Zone 1 Temperature ⁷ 250 - 280 °C - Mold Temperature ⁷ 90 - 120 °C - Back Pressure ⁷ 1 - 5 MPa - Screw Speed ⁷ 30 - 100 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Country Availability
- Regional Availability