Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Strain (Break) ¹¹ 6.2 % ISO 527 Tensile Strain (Yield) ¹¹ 1.9 % ISO 527 Tensile Stress (Break) ¹¹ 188 MPa ISO 527 Tensile Stress (Yield) ¹¹ 188 MPa ISO 527 Tensile Modulus (at 1 mm/min) ¹¹ 19200 MPa ISO 527 Flexural Modulus (at 2 mm/min) ¹¹ 17000 MPa ISO 178 Flexural Strength (at 2 mm/min) ¹¹ 280 MPa ISO 178 Tensile Stress (Yield, Type I, 5 mm/min) ¹¹ 173 MPa ASTM D638 Tensile Stress (Break, Type I, 5 mm/min) ¹¹ 173 MPa ASTM D638 Tensile Strain (Yield, Type I, 5 mm/min) ¹¹ 1.9 % ASTM D638 Tensile Strain (Break, Type I, 5 mm/min) ¹¹ 2 % ASTM D638 Tensile Modulus (at 5 mm/min) ¹¹ 19850 MPa ASTM D638 Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ 282 MPa ASTM D790 Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ 16540 MPa ASTM D790 - Physical Properties
Value Units Test Method / Conditions Density ¹¹ 1.32 g/cm³ ISO 1183 Density ¹¹ 1.32 g/cm³ ASTM D792 Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ 0.4 % ASTM D955 Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ 0.35 % ISO 294 Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ 0.8 % ASTM D955 Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ 0.8 % ISO 294 Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ 0.1 % ASTM D570 Wear Factor Washer ¹¹ 15 10^-10 in^5-min/ft-lb-hr ASTM D3702 Modified: Manual Dynamic COF ¹¹ 0.46 - ASTM D3702 Modified: Manual Static COF ¹¹ 0.46 - ASTM D3702 Modified: Manual - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 212 °C ISO 75/Af Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 222 °C ISO 75/Bf Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ 0.0000252 1/°C ASTM E831 Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹ 0.000026 1/°C ISO 11359-2 Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ 0.0000486 1/°C ASTM E831 Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹ 0.000048 1/°C ISO 11359-2 Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ 221 °C ASTM D648 Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 212 °C ASTM D648 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Unnotched, at 23°C) ¹¹ 801 J/m ASTM D4812 Izod Impact (Notched, at 23°C) ¹¹ 53 J/m ASTM D256 Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹ 6 J ASTM D3763 Multi-Axial Impact ¹¹ 3 J ISO 6603 Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ 49 kJ/m² ISO 180/1U Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 7 kJ/m² ISO 180/1A - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 80 °C - Drying Time ⁷ 4 Hrs - Maximum Moisture Content ⁷ 0.12 - 0.2 % - Melt Temperature ⁷ 270 - 275 °C - Front - Zone 3 Temperature ⁷ 270 - 280 °C - Middle - Zone 2 Temperature ⁷ 260 - 270 °C - Rear - Zone 1 Temperature ⁷ 250 - 260 °C - Mold Temperature ⁷ 80 - 95 °C - Back Pressure ⁷ 0.2 - 0.3 MPa - Screw Speed ⁷ 30 - 60 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Regional Availability