Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Physical Properties
Value Units Test Method / Conditions Dynamic COF ¹¹ 0.57 - ASTM D3702 Modified: Instr. Static COF ¹¹ 0.99 - ASTM D3702 Modified: Instr. Wear Factor Washer ¹¹ 10 10^-10 in^5-min/ft-lb-hr ASTM D3702 Modified: Instr. Density ¹¹ 1.44 g/cm³ ISO 1183 Mold Shrinkage (flow) ᵍ ¹¹ 0.1 - 0.3 % SABIC method - Mechanical Properties
Value Units Test Method / Conditions Tensile Modulus (at 1 mm/min) ¹¹ 10200 MPa ISO 527 Tensile Stress (Break, 5 mm/min) ¹¹ 250 MPa ISO 527 Tensile Strain (Break, 5 mm/min) ¹¹ 4.2 % ISO 527 Flexural Modulus (at 2 mm/min) ¹¹ 8600 MPa ISO 178 Flexural Stress (Break, 2 mm/min) ¹¹ 165 MPa ISO 178 Flexural Strain (Break, at 2 mm/min) ¹¹ 3.9 % ISO 178 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 219 °C ISO 75/Bf Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 206 °C ISO 75/Af Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ 0.000024 1/°C ISO 11359-2 Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ 0.000075 1/°C ISO 11359-2 Relative Temperature Index (Electrical) ᵖ ¹¹ 65 °C UL 746B Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ 65 °C UL 746B Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ 65 °C UL 746B - Electrical Properties
Value Units Test Method / Conditions Comparative Tracking Index (UL, PLC) ᵖ ¹¹ 1 PLC Code UL 746A Hot Wire Ignition (PLC 0) ᵖ ¹¹ min. 2.5 mm UL 746A Hot Wire Ignition (PLC 1) ᵖ ¹¹ min. 1.5 mm UL 746A High Ampere Arc Ignition (PLC 0) ᵖ ¹¹ min. 1.5 mm UL 746A - Impact Properties
Value Units Test Method / Conditions Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 14 kJ/m² ISO 180/1A Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ 98 kJ/m² ISO 180/1U - Injection Molding
Value Units Test Method / Conditions Back Pressure ⁷ 0.2 - 0.3 MPa - Drying Temperature ⁷ 80 °C - Drying Time ⁷ 4 Hrs - Front - Zone 3 Temperature ⁷ 295 - 305 °C - Maximum Moisture Content ⁷ 0.15 - 0.25 % - Melt Temperature ⁷ 280 - 305 °C - Middle - Zone 2 Temperature ⁷ 280 - 295 °C - Mold Temperature ⁷ 95 - 110 °C - Rear - Zone 1 Temperature ⁷ 265 - 275 °C - Screw Speed ⁷ 30 - 60 rpm - - Flame Characteristics
Value Units Test Method / Conditions UL Recognized (94HB Flame Class Rating) ᵖ min. 1.5 mm UL 94 UV-light (Water exposure/immersion) ᵖ F1 - UL 746C - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Regional Availability