Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Break, 5 mm/min) ¹¹ 153 MPa ISO 527 Tensile Stress (Break) ¹¹ 158 MPa ASTM D638 Tensile Strain (Break, 5 mm/min) ¹¹ 0.7 % ISO 527 Tensile Strain (Break) ¹¹ 1 - 3 % ASTM D638 Flexural Modulus ¹¹ 23160 MPa ASTM D790 Tensile Modulus (at 1 mm/min) ¹¹ 25000 MPa ISO 527 Flexural Stress (Yield, at 2 mm/min) ¹¹ 261 MPa ISO 178 Flexural Stress (Break, 2 mm/min) ¹¹ 217 MPa ISO 178 Flexural Strain (Break, at 2 mm/min) ¹¹ 1.3 % ISO 178 Flexural Modulus (at 2 mm/min) ¹¹ 21200 MPa ISO 178 Flexural Strain (Break, at 2 mm/min, 80°C) ¹¹ 1.3 % ISO 178 Flexural Strain (Break, at 2 mm/min, 120°C) ¹¹ 2.3 % ISO 178 Flexural Strain (Break, at 2 mm/min, 150°C) ¹¹ 2.4 % ISO 178 Flexural Strain (Break, at 2 mm/min, 200°C) ¹¹ 2.4 % ISO 178 Flexural Stress (Yield, at 2 mm/min, 80°C) ¹¹ 212 MPa ISO 178 Flexural Stress (Yield, at 2 mm/min, 120°C) ¹¹ 118 MPa ISO 178 Flexural Stress (Yield, at 2 mm/min, 150°C) ¹¹ 94 MPa ISO 178 Flexural Stress (Yield, at 2 mm/min, 200°C) ¹¹ 66 MPa ISO 178 Flexural Modulus (at 2 mm/min, 80°C) ¹¹ 20600 MPa ISO 178 Flexural Modulus (at 2 mm/min, 120°C) ¹¹ 10200 MPa ISO 178 Flexural Modulus (at 2 mm/min, 150°C) ¹¹ 7900 MPa ISO 178 Flexural Modulus (at 2 mm/min, 200°C) ¹¹ 6100 MPa ISO 178 - Physical Properties
Value Units Test Method / Conditions Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ 0.19 % ISO 294 Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ 0.95 % ISO 294 Wear Factor Washer ¹¹ 19 10^-10 in^5-min/ft-lb-hr ASTM D3702 Modified: Manual Dynamic COF ¹¹ 0.39 - ASTM D3702 Modified: Manual Density ¹¹ 1.52 g/cm³ ISO 1183 Water Absorption (at 23°C, 24hrs) ¹¹ 0.05 % ISO 62-1 Moisture Absorption (at 23°C, 50% RH) ¹¹ 0.03 % ISO 62 Melt Volume Rate (at 315°C, 5.0 kg) ¹¹ 4 - 6 cm³/10 min ISO 1133 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 264 °C ASTM D648 Specific Heat ¹¹ 1633 J/kg-K ASTM E1269 Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹ 0.000003 1/°C ISO 11359-2 Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹ 0.000049 1/°C ISO 11359-2 Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 278 °C ISO 75/Bf Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 255 °C ISO 75/Af Thermal Conductivity ¹¹ 0.36 W/m-K ASTM D5930 - Electrical Properties
Value Units Test Method / Conditions Surface Resistivity ¹¹ 10 - 1000 Ω ASTM D257 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Notched, at 23°C) ¹¹ 48 J/m ASTM D256 Izod Impact (Notched, 80*10*3, at -40°C) ¹¹ 6 kJ/m² ISO 180/1A Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ 26 kJ/m² ISO 180/1U Izod Impact (Unnotched, 80*10*4, at -40°C) ¹¹ 23 kJ/m² ISO 180/1U Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 6 kJ/m² ISO 180/1A - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 120 - 150 °C - Drying Time ⁷ 4 Hrs - Melt Temperature ⁷ 315 - 320 °C - Front - Zone 3 Temperature ⁷ 330 - 345 °C - Middle - Zone 2 Temperature ⁷ 320 - 330 °C - Rear - Zone 1 Temperature ⁷ 305 - 315 °C - Mold Temperature ⁷ 140 - 165 °C - Back Pressure ⁷ 0.2 - 0.3 MPa - Screw Speed ⁷ 30 - 60 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Regional Availability