Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Modulus (at 1 mm/min) ¹¹ 2170 MPa ISO 527 Tensile Stress (Yield, 50 mm/min) ¹¹ 50 MPa ISO 527 Tensile Strain (Yield, 50 mm/min) ¹¹ 5 % ISO 527 Tensile Stress (Break, 50 mm/min) ¹¹ 44 MPa ISO 527 Tensile Strain (Break, 50 mm/min) ¹¹ 67 % ISO 527 Flexural Modulus (at 2 mm/min) ¹¹ 2090 MPa ISO 178 Tensile Modulus (at 50 mm/min) ¹¹ 2280 MPa ASTM D638 Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ 56 MPa ASTM D638 Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ 5 % ASTM D638 Tensile Stress (Break, Type I, 50 mm/min) ¹¹ 46 MPa ASTM D638 Tensile Strain (Break, Type I, 50 mm/min) ¹¹ 86 % ASTM D638 Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ 2180 MPa ASTM D790 - Physical Properties
Value Units Test Method / Conditions Density ¹¹ 1.12 g/cm³ ISO 1183 Dynamic COF ¹¹ 0.33 - ASTM D3702 Modified: Manual Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ 0.097 % ASTM D570 Mold Shrinkage (flow) ᵍ ¹¹ 0.7 - 0.9 % SABIC method Mold Shrinkage (xflow) ᵍ ¹¹ 0.8 - 1 % SABIC method Melt Volume Rate (at 260°C, 5.0 kg) ¹¹ 21 cm³/10 min ISO 1133 Melt Flow Rate (at 260°C, 5.0 kgf) ¹¹ 23 g/10 min ASTM D1238 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 104 °C ISO 75/Af Vicat Softening Temperature (Rate B/50) ¹¹ 126 °C ISO 306 Vicat Softening Temperature (Rate B/120) ¹¹ 124 °C ISO 306 Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ 125 °C ASTM D648 Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 103 °C ASTM D648 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ 208 kJ/m² ISO 180/1U Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 40 kJ/m² ISO 180/1A Izod Impact (Unnotched, 80*10*4, at -30°C) ¹¹ 248 kJ/m² ISO 180/1U Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ 14 kJ/m² ISO 180/1A Izod Impact (Notched, 80*10*4, at -40°C) ¹¹ 14 kJ/m² ISO 180/1A Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ 402 kJ/m² ISO 179/1eU Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ 49 kJ/m² ISO 179/1eA Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ 16 kJ/m² ISO 179/1eA Charpy Impact (at -40°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ 16 kJ/m² ISO 179/1eA Izod Impact (Notched, at 23°C) ¹¹ 747 J/m ASTM D256 Izod Impact (Notched, at -30°C) ¹¹ 463 J/m ASTM D256 - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 105 - 110 °C - Drying Time (Cumulative) ⁷ 3 - 4 Hrs - Drying Time (Cumulative) ⁷ 9 Hrs - Maximum Moisture Content ⁷ 0.02 % - Melt Temperature ⁷ 275 - 300 °C - Front - Zone 3 Temperature ⁷ 260 - 300 °C - Middle - Zone 2 Temperature ⁷ 255 - 295 °C - Rear - Zone 1 Temperature ⁷ 250 - 290 °C - Mold Temperature ⁷ 60 - 80 °C - Back Pressure ⁷ 0.3 - 0.7 MPa - Screw Speed ⁷ 40 - 70 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Regional Availability