Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Physical Properties
Value Units Test Method / Conditions Melt Flow Rate (at 400°C, 5.0 kgf) ¹¹ 32 g/10 min ASTM D1238 Specific Gravity ¹¹ 1.45 - ASTM D792 Poisson's Ratio ¹¹ 0.43 - ISO 527-1/2 Wear Factor Washer ¹¹ 14 10^-10 in^5-min/ft-lb-hr ASTM D3702 Modified: Manual Dynamic COF ¹¹ 0.37 - ASTM D3702 Modified: Manual Static COF ¹¹ 0.35 - ASTM D3702 Modified: Manual - Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Break, Type I, 5 mm/min) ¹¹ 185 MPa ASTM D638 Tensile Strain (Break, Type I, 5 mm/min) ¹¹ 1.8 % ASTM D638 Tensile Modulus (at 5 mm/min) ¹¹ 16000 MPa ASTM D638 Flexural Stress (Break, 1.3 mm/min, 50 mm span) ¹¹ 277 MPa ASTM D790 Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ 13400 MPa ASTM D790 Tensile Stress (Break, 5 mm/min) ¹¹ 181 MPa ISO 527 Tensile Strain (Break, 5 mm/min) ¹¹ 1.6 % ISO 527 Tensile Modulus (at 1 mm/min) ¹¹ 13960 MPa ISO 527 Flexural Stress ¹¹ 276 MPa ISO 178 Flexural Modulus (at 2 mm/min) ¹¹ 13530 MPa ISO 178 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 320 °C ASTM D648 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Notched, at 23°C) ¹¹ 69 J/m ASTM D256 Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 5 kJ/m² ISO 180/1A - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 150 °C - Drying Time ⁷ 4 - 6 Hrs - Front - Zone 3 Temperature ⁷ 380 - 400 °C - Middle - Zone 2 Temperature ⁷ 380 - 400 °C - Rear - Zone 1 Temperature ⁷ 370 - 380 °C - Mold Temperature ⁷ 175 - 190 °C - Back Pressure ⁷ 0.3 - 0.7 MPa - Screw Speed ⁷ 60 - 100 rpm - - Note
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Regional Availability