Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Color
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Yield, 50 mm/min) ¹¹ 62 MPa ASTM D638 Tensile Stress (Break, 50 mm/min) ¹¹ 68 MPa ASTM D638 Tensile Strain (Yield, at 50 mm/min) ¹¹ 6 % ASTM D638 Tensile Modulus (at 50 mm/min) ¹¹ 2210 MPa ASTM D638 Hardness (Rockwell R) ¹¹ 118 - ASTM D785 Tensile Stress (Yield) ¹¹ 62 MPa ISO 527 Tensile Stress (Break) ¹¹ 68 MPa ISO 527 Tensile Strain (Yield) ¹¹ 6 % ISO 527 Tensile Strain (Break) ¹¹ 150 % ISO 527 Flexural Stress ¹¹ 98 MPa ISO 178 Flexural Modulus (at 2 mm/min) ¹¹ 2400 MPa ISO 178 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.2 - ASTM D792 Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹ 0.15 % ASTM D570 Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ 0.5 - 0.5 % ASTM D955 Moisture Absorption (at 23°C, 50% RH) ¹¹ 0.32 % ISO 62 Melt Volume Rate (at 300°C, 1.2 kg) ¹¹ 12 cm³/10 min ISO 1133 - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 122 °C ASTM D648 Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ 120 °C ISO 75/Af - Electrical Properties
Value Units Test Method / Conditions Volume Resistivity ¹¹ 2.00E+17 Ω.cm ASTM D257 Dielectric Constant (at 1 MHz) ¹¹ 3 - ASTM D150 Dissipation Factor (at 100 Hz) ¹¹ 0.001 - ASTM D150 Dissipation Factor (at at 1 MHz) ¹¹ 0.002 - ASTM D150 - Optical Properties
Value Units Test Method / Conditions Refractive Index ¹¹ 1.586 - ASTM D542 Refractive Index ¹¹ 1.586 - ISO 489 - Impact Properties
Value Units Test Method / Conditions Izod Impact (Unnotched, at 23°C) ¹¹ No break J/m ASTM D4812 Izod Impact (Notched, at 23°C) ¹¹ 750 J/m ASTM D256 Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ 75 kJ/m² ISO 180/1A Charpy Impact (Notched, at 23°C) ¹¹ 25 kJ/m² ISO 179/2C Charpy Impact (Notched, at -30°C) ¹¹ 12 kJ/m² ISO 179/2C - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 120 °C - Drying Time ⁷ 4 Hrs - Maximum Moisture Content ⁷ 0.02 % - Melt Temperature ⁷ 305 - 325 °C - Front - Zone 3 Temperature ⁷ 320 - 330 °C - Middle - Zone 2 Temperature ⁷ 310 - 320 °C - Rear - Zone 1 Temperature ⁷ 295 - 305 °C - Mold Temperature ⁷ 80 - 110 °C - Back Pressure ⁷ 0.2 - 0.3 MPa - Screw Speed ⁷ 30 - 60 rpm - - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Packaging & Availability
- Regional Availability