Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Break, Type I, 50 mm/min) ¹¹ 6 MPa ASTM D638 Tensile Strain (Break, Type I, 50 mm/min) ¹¹ 150 % ASTM D638 Flexural Modulus (at 12.5 mm/min, 100 mm span) ¹¹ 50 MPa ASTM D790 Hardness (Shore A, 30S reading) ¹¹ 84 - ASTM D2240 Tensile Stress (Break, 50 mm/min) ¹¹ 7 MPa ISO 527 Tensile Strain (Break, 50 mm/min) ¹¹ 175 % ISO 527 Flexural Modulus (at 12.5 mm/min) ¹¹ 50 MPa ISO 178 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.01 - ASTM D792 Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹ 0.95 % ASTM D955 Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹ 0.75 % ASTM D955 Melt Flow Rate (at 210°C, 5 kgf) ¹¹ 24 g/10 min ASTM D1238 Melt Flow Rate (at 250°C, 2.16 kgf) ¹¹ 27 g/10 min ASTM D1238 - Electrical Properties
Value Units Test Method / Conditions Volume Resistivity ¹¹ 7.10E+15 Ω.cm ASTM D257 Comparative Tracking Index ʳ ¹¹ 600 V IEC 60112 Comparative Tracking Index (UL, PLC) ¹¹ 0 PLC Code UL 746A - Impact Properties
Value Units Test Method / Conditions Brittleness Temperature ¹¹ max. -40 °C ASTM D746 - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 60 - 80 °C - Drying Time ⁷ 4 - 6 Hrs - Drying Time (Cumulative) ⁷ 8.00E+00 Hrs - Maximum Moisture Content ⁷ 0.01 % - Melt Temperature ⁷ 220 - 250 °C - Nozzle Temperature ⁷ 220 - 250 °C - Front - Zone 3 Temperature ⁷ 220 - 250 °C - Middle - Zone 2 Temperature ⁷ 210 - 240 °C - Rear - Zone 1 Temperature ⁷ 180 - 220 °C - Mold Temperature ⁷ 40 - 60 °C - Back Pressure ⁷ 3 - 10 MPa - Screw Speed ⁷ 30 - 80 rpm - Shot to Cylinder Size ⁷ 30 - 70 % - Vent Depth ⁷ 0.03 - 0.05 mm - - Flame Characteristics
Value Units Test Method / Conditions UL Recognized (94HB Flame Class Rating) ʳ min. 0.6 mm UL 94 UL Recognized (94V-0 Flame Class Rating) ʳ min. 6 mm UL 94 Glow Wire Flammability Index (passes at 750°C) ʳ 3 mm IEC 60695-2-12 Glow Wire Ignitability Temperature (at 3.0 mm) ʳ 750 °C IEC 60695-2-13 - Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability