Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Break, Type I, 50 mm/min) ¹¹ 15 MPa ASTM D638 Tensile Strain (Break, Type I, 50 mm/min) ¹¹ 245 % ASTM D638 Flexural Modulus (at 12.5 mm/min, 100 mm span) ¹¹ 20 MPa ASTM D790 Hardness (Shore A, 30S reading) ¹¹ 81 - ASTM D2240 Tensile Stress (Break, 50 mm/min) ¹¹ 17 MPa ISO 527 Tensile Strain (Break, 50 mm/min) ¹¹ 260 % ISO 527 Flexural Modulus (at 12.5 mm/min) ¹¹ 20 MPa ISO 178 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.03 - ASTM D792 Melt Flow Rate (at 250°C, 10.0 kgf) ¹¹ 10 g/10 min ASTM D1238 - Typical Properties
Value Units Test Method / Conditions Tensile Strength (Break) ¹⁹ 22 MPa UL 1581 Tensile Elongation (Break) ¹⁹ 330 % UL 1581 Tensile Strength (Break, after 7days, at 136°C) ¹⁹ 23 MPa UL 1581 Tensile Elongation (Break, after 7days, at 136°C) ¹⁹ 290 % UL 1581 Heat Deformation (at 121°C, 250g) ¹⁹ 10 % UL 1581 VW-1 ¹⁹ Pass - UL 1581 - Electrical Properties
Value Units Test Method / Conditions Volume Resistivity ¹¹ 5.10E+15 Ω.cm ASTM D257 Surface Resistivity ¹¹ 1.60E+16 Ω ASTM D257 Dielectric Strength (in oil, at 2mm) ¹¹ 25 kV/mm ASTM D149 Comparative Tracking Index ¹¹ 600 V IEC 60112 Dielectric Constant (at 5 GHz) ¹¹ 2.6 - SABIC method Dissipation Factor (at 5 GHz) ¹¹ 0.002 - SABIC method - Flame Characteristics
Value Units Test Method / Conditions Oxygen Index (LOI) 27 % ISO 4589 Smoke Density (on 0.5mm plaque, Non-Flame, Ds-max) 166 - ASTM E662 Smoke Density (on 0.5mm plaque, Flame, Ds-max) 117 - ASTM E662 Glow Wire Flammability Index (passes at 850°C) 3 mm IEC 60695-2-12 Glow Wire Ignitability Temperature (at 3.0 mm) 775 °C IEC 60695-2-13 - Wire Coating Extrusion
Value Units Test Method / Conditions Conductor Pre-heat Temperature 25 - 120 °C - Cooling Water Air Gap 100 - 200 mm - Cross-head Temperature 220 - 250 °C - Die Temperature 220 - 250 °C - Drying Temperature 75 - 85 °C - Drying Time 5 - 7 Hrs - Drying Time (Cumulative) 12 Hrs - Extruder Length/Diameter Ratio (L/D) 22:1 to 26:1 - - Feed Zone Temperature 180 - 220 °C - Head Zone Temperature 220 - 250 °C - Maximum Moisture Content 0.02 % - Melt Temperature 220 - 250 °C - Middle Zone Temperatures 220 - 250 °C - Neck Temperature 220 - 250 °C - Screen Pack 150 - 100 - - Screw Speed 15 - 85 rpm - Water Bath Temperature 15 - 60 °C - - Note
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
- ¹⁹ Wire and cable - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability