Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
Value Units Test Method / Conditions Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ 60 MPa ASTM D638 Tensile Stress (Break, Type I, 50 mm/min) ¹¹ 47 MPa ASTM D638 Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ 4 % ASTM D638 Tensile Strain (Break, Type I, 50 mm/min) ¹¹ 40 % ASTM D638 Tensile Modulus (at 50 mm/min) ¹¹ 2500 MPa ASTM D638 Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹ 90 MPa ASTM D790 Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ 2400 MPa ASTM D790 - Physical Properties
Value Units Test Method / Conditions Specific Gravity ¹¹ 1.18 - ASTM D792 Water Absorption (at 23°C, 24hrs) ¹¹ 0.1 % ASTM D570 Mold Shrinkage (flow, 3.2 mm) ʰ ¹¹ 0.4 - 0.6 % SABIC method Mold Shrinkage (xflow, 3.2 mm) ʰ ¹¹ 0.4 - 0.6 % SABIC method Melt Flow Rate (at 260°C, 2.16 kgf) ¹¹ 21 g/10 min ASTM D1238 - Thermal Properties
Value Units Test Method / Conditions Vicat Softening Temperature (Rate B/50) ¹¹ 100 °C ASTM D1525 Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ 85 °C ASTM D648 Heat Deflection Temperature (at 0.45 MPa, 6.4 mm, Unannealed) ¹¹ 101 °C ASTM D648 Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹ 92 °C ASTM D648 Coefficient of Thermal Expansion (at -40°C to 60°C, flow) ¹¹ 0.000071 1/°C ASTM E831 Coefficient of Thermal Expansion (at -40°C to 60°C, xflow) ¹¹ 0.000072 1/°C ASTM E831 Relative Temperature Index (Electrical) ᵖ ¹¹ 85 °C UL 746B Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ 85 °C UL 746B Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ 85 °C UL 746B - Electrical Properties
Value Units Test Method / Conditions Hot Wire Ignition (PLC 2) ¹¹ min. 3 mm UL 746A - Impact Properties
Value Units Test Method / Conditions Izod Impact (Notched, at 23°C) ¹¹ 500 J/m ASTM D256 Instrumented Dart Impact Total Energy (at 23°C) ¹¹ 50 J ASTM D3763 Izod Impact (Notched, 80*10*3, at 23°C) ¹¹ 51 kJ/m² ISO 180/1A - Injection Molding
Value Units Test Method / Conditions Drying Temperature ⁷ 80 - 90 °C - Drying Time ⁷ 3 - 4 Hrs - Drying Time (Cumulative) ⁷ 8 Hrs - Maximum Moisture Content ⁷ 0.04 % - Melt Temperature ⁷ 245 - 275 °C - Nozzle Temperature ⁷ 245 - 275 °C - Front - Zone 3 Temperature ⁷ 245 - 275 °C - Middle - Zone 2 Temperature ⁷ 220 - 265 °C - Rear - Zone 1 Temperature ⁷ 220 - 255 °C - Mold Temperature ⁷ 60 - 80 °C - Back Pressure ⁷ 0.3 - 0.7 MPa - Screw Speed ⁷ 40 - 70 rpm - Shot to Cylinder Size ⁷ 30 - 80 % - Vent Depth ⁷ 0.038 - 0.076 mm - - Flame Characteristics
Value Units Test Method / Conditions UL Recognized (94V-0 Flame Class Rating) ᵖ min. 1.5 mm UL 94 UL Recognized (94V-1 Flame Class Rating) ᵖ min. 1.2 mm UL 94 UL Recognized (94HB Flame Class Rating) ᵖ min. 0.3 mm UL 94 - Note
- ʰ Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Regional Availability