Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Typical Uses
EPO-205 can be used over troweled colored quartz (CQ), broadcast colored quartz (CQ), or colored flake (CF) systems. EPO-205 can also be used to seal cove base and on vertical wall surfaces. EPO-205 is ideal for light to moderate traffic areas, general manufacturing or distribution facilities, or aircraft hangars.
- Cure Time
10 hrs (foot traffic and recoat), 13 hrs (full service) at& 75°F and 70% RH.
- Application of Materials
If pigment is required, mix pigment into part A prior to mixing with part B. Use a variable speed drill equipped with a jiffy mixing blade; mix on low speed until evenly dispersed. Once fully blended, mix A & B using a variable speed drill equipped with a jiffy mixing blade until well blended for a minimum of two minutes. Scrape sides of mixing bucket with paint stick or spatula to help insure thorough blending of parts A and B. If no pigment is required, mix 2 parts A with 1 part B by volume. Using a variable speed drill equipped with a jiffy mixing blade; mix on low speed until well blended for a minimum of two minutes. Scrape sides of mixing bucket with paint stick or spatula to help insure thorough blending of parts A and B. Apply EPO-205 material to floor immediately after mixing by using a brush, roller, squeegee, or trowel. Rate of application will vary based on system selected. Refer to appropriate system specification for detailed application rates. If a second coat is required, it must be applied within 20 hours, otherwise the surface must be sanded with 60 grit sandpaper prior to application. Application temperature should be between 60ºF and 80ºF. Substrate temperature must be a minimum of 5ºF above dew point. Use xylene, acetone, etc. for cleaning tools and equipment soon after use. Do not use solvents on hands or other parts of body. Clean hands and other exposed areas with soap and water.
Properties
- Physical Properties
Value Units Test Method / Conditions Density 9.15 lbs / gal ASTM D1475 Heat Distortion Temperature (264-psi load) 120.0 °F - Mix Ratio (A:B, V:V) 2:1 - - Hardness 85 Shore D Taber Abrasion 102.0 - ASTM D4060 Tensile Strength 3000.0 psi ASTM D638/C307 Viscosity 4000.0 cps ASTM D2196 Volume Solids 100.0 % - - Properties
- Excellent resistance to staining and chemicals, such as acids, alkalis, and solvents.
- Zero VOC
- Low odor - reduces the need to relocate personnel during application.
- Improved UV resistance over traditional epoxy.
- Excellent color stability.
- Impact resistant
- Seamless
- Nonporous
- Durable and low maintenance.
- Orange peel surface appearance.
Safety & Health
- Caution
Workers should wear protective clothing, eye protection, and impermeable gloves. If allowable exposure limits are exceeded, organic vapor respirators should be worn. All on-site personnel should become familiar with the SDS and appropriate system specification in order to increase hazard awareness.
Packaging & Availability
- Standard Packaging
- 15 gallon kit (2 parts A, 1 part B, in 5 gallon pails)
- 3 gallon kit (2 parts A, 1 part B, in 1 gallon pails)
- Pigment: 1 quart can (mix 1 quart: 3 gallon kit).
Storage & Handling
- Pot Life
25 minute at 77°F.
- Shelf Life
1 yr. from ship date (unopened) at 73ºF.
- Storage Condition
Store material in a cool and dry place out of direct sunlight. For best results material should be stored between 70ºF and 90ºF. Do not store near open flame or ignition source. Read and understand all product labels and Safety Data Sheets (SDS) prior to use.