Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Fluids & Lubricants Functions
- Base Material
- Water
- Technologies
- Product Families
Features & Benefits
- Fluids & Lubricants Features
- Features
- Vector HTS lapping additive is designed for high-speed single-pass systems.
- Vector HTS improves the lapping process by reducing variability, and lowers cost through reduction in required abrasives
- Product Highlights
- Produces flatter wafers.
- Facilitates post-lapping cleaning.
- Reduces wafer damage.
- Provides more consistent results.
- Increases cut rate.
- Helps prevent wafer staining.
- Helps to eliminate scratching.
- Features
- Vector HTS lapping additive is designed for high-speed single-pass systems.
- Vector HTS improves the lapping process by reducing variability, and lowers cost through reduction in required abrasives.
- Product Highlights
- Produces flatter wafers.
- Facilitates post-lapping cleaning.
- Reduces wafer damage.
- Provides more consistent results.
- Increases cut rate.
- Helps prevent wafer staining.
- Helps to eliminate scratching.
Applications & Uses
- Markets
- Applications
- Compatible Substrates & Surfaces
- Fluids & Lubricants Type
- Fluids & Lubricants End Use
- Dilution Ratio
- 25:1
- Typical Applications
- Gallium arsenide, Germanium, Sapphire, Silicon, Silicon carbide
- Pureon offers a wide range of customize tailored solutions
- Applications
Gallium arsenide, Germanium, Sapphire, Silicon, Silicon carbide.
Properties
- Typical Properties
Value Units Test Method / Conditions Dilution Ratio 25:01:00 - - pH Value 9.0 - - pH Value 9.1 - - Specific Gravity 1.0 - - Specific Gravity 1 - -
Packaging & Availability
Storage & Handling
- Shelf Life
- 24 Months
- Shelf Life
24 months
- Instructions
Handling
- Vector HTS Products should be mixed with deionized water and abrasive using the following slurry formula: 77 - 82% water, 15 - 18% abrasive, 3 - 5% HTS Product. Use an agitator with a marine type propeller and a motor capable of 1750 RPM. Use a low shear dispense pump for feeding the mixed slurry onto the lap.
- Disperse the abrasive with DI water between 500 and 1500 rpm for 10 minutes. Add HTS Product. Mix for approximately 5 - 10 minutes. Avoid sucking air into the slurry during mixing. A small vortex should form at the surface of the slurry when the product is mixed. Afterwards, turn the mixer off, or to a maximum of 50 rpm.
Storage
- Product should be stored in a temperature controlled environment. Prolonged exposure to temperatures at or below 32° Fahrenheit (0°C) is discouraged. Prolonged exposure to temperatures at or above 100° Fahrenheit (38°C) is also discouraged. In addition, material should always be sealed when not in use to prevent evaporation.
Disposal
- Dispose of in accordance with all applicable local regulations.
- Instructions
Handling
- Vector HTS Products should be mixed with deionized water and abrasive using the following slurry formula: 77-82% water, 15-18% abrasive, 3-5% HTS Product. Use an agitator with a marine type propeller and a motor capable of 1750 RPM. Use a low shear dispense pump for feeding the mixed slurry onto the lap. Disperse the abrasive with DI water between 500 and 1500 rpm for 10 minutes. Add HTS Product. Mix for approximately 5-10 minutes. Avoid sucking air into the slurry during mixing. A small vortex should form at the surface of the slurry when the product is mixed. Afterwards, turn the mixer off, or to a maximum of 50 rpm.
Storage
- Product should be stored in a temperature controlled environment. Prolonged exposure to temperatures at or below 32° Fahrenheit (0°C) is discouraged. Prolonged exposure to temperatures at or above 100° Fahrenheit (38°C) is also discouraged. In addition, material should always be sealed when not in use to prevent evaporation.
Disposal
- Dispose of in accordance with all applicable local regulations.