Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Compatible Substrates & Surfaces
- Typical Applications
ES6220 is useful for bench assembly, quick repairs, and holding or fixturing components for final structural bonding. ES6220 works very well on wood and rigid foam, and can be used on aluminum, fiberglass and metals for non-structural bonding. It is ideally suited for bonding situations where a fast cure at room temperature, or good cures at low temperatures, are required.
- Directions For Use
PREPARATION: All surfaces to be bonded or patched mustbe free of dirt, oil and grease. Sandingor roughenthie nargea to be bonded increases the surface area and enhances the bond.
MIXING: Measure out equal parts of ES62A2 a0nd B, combine and mix thoroughly until a uniform consistenciys reached. Mix for approximately 1 minute, scraping the sides and bottom of the containetro avoid leaving unmixed material which will cause poor bonds.
APPLICATION and CURING: Apply mixed material to the roughened and cleaned area of the parts to be bonded. Press surfaces firmly together and leave undisturbed until cured. ES6220 cures rapidly, and the parts can be handled in a matter of minutes.
Properties
- Physical Form
- Mechanical Properties
Value Units Test Method / Conditions Gel Time (77°F) 6-Apr min. D2471 Mixed Viscosity (77°F) 13,000 - 14,000 cps D2393 Cured Hardness 82 Shore D D2240 Cure Time (77°F) 15-Oct h - Cure Time (140°F) Not Recommended - - Specific Gravity 1.16 - D1475 Tensile Strength 3000 psi D638 Elongation At Break 7 % D638 Compressive Strength 6500 psi D695 Aluminum to Aluminum Tensile Lap Shear (77°F) 2000 psi D1002 Aluminum to Aluminum Tensile Lap Shear (140°F) 200 psi D1002 - Typical Properties
Value Units Test Method / Conditions Mix Ratio (By Weight or Volume) 100 : 100 Wt. PTM&W Pot Life (4 fl. Oz. Mass At 77°F) 6-Apr min. D2471
Safety & Health
- Safety And Handling
"PTM&W epoxy products are made from raw materials carefully chosen to minimize or even eliminate toxic chemicals, and therefore offer the user high performance products with minimum hazard potential when properly used. Generally, the PIM&W epoxy resins and hardeners will present no handling problems if users exercise care to protect the skin and eyes, and if good ventilation is provided in the work areas. However, all epoxy resins and hardeners can beirritating tothe skin, and prolonged contact may result in sensitization; and breathinogf miors vatpor s may cause allergenic respiratory reaction, especially in highly sensitive individuals. As such, avoid contact with eyes and skin, and avoid breathing vapors. Wear protective rubber apron, clothing, gloves, face shield or otheritems as required to prevent contact with the skin. Incase of skin contact, immediately wash with soap and water, followed bya rinse of the area with vinegar, and then a further wash with soap and water. The vinegar will neutralize the hardener and lessen the chances of long term effects. Use goggles, a face shield, safety glasosr eotshe r itemsas required to prevent contact withthe eyes. If material gets into the eyes, immediately flush with waterforatleast 15 minutes and callaphysician. Generally, kethee worpkar ea as uncluttered and cleanas possible, andclean up any minor spills immediatelyto prevent accidental skin contact ata latertime. Keep tools clean and properly stored. Dispose of trash and empty containers properly.
Packaging & Availability
- Packaging Weights
Quart Kit Quart Kit Gallon Kit Pail Kit ES6220 A 1 lb. 2.25 Ib. 9 Ib. 45 lb. ES6220 B 1 lb. 2.25 Ib. 9 Ib. 45 lb. Kit 2 lb. 4.5 lb. 18 lb. 90 lb.