Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Coating Type
- Acrylic
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- Thermally Insulating
- Mold Resistant
- Solar Reflecting
- Mold Resistant
- Hydrophobic
- Keep buildings cooler/hotter in varied climates
- Reduce expensive AC/heating bills
- Safe touch solution
- Easy to apply - tough & durable
- Low VOC (low environmental impact)
- Safe for multiple materials (ie, tents to walls)
- Water Based / Acrylic Resin
- High fire resistance
- Mold resistant
- Water-proof
Applications & Uses
- Markets
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Applications
Achieve Exceptional Thermal Insulation:
- Homes
- Warehouses
- Mobile Shelters
- RV’s
- Fridge/Freezers
- Industrial Settings
- Surface Preparation
- All surfaces to be coated should be completely clean, dry and free from contamination. Surface preparation method shall be in accordance with ISO 8504: 2000.
- Remove salt and other water-soluble contaminants by fresh water.
- Remove oil and grease with suitable detergent or solvent (SSPC-SP-1).
- Remove rust, mill scale and other loose material completely by abrasive blasting (ISO 8501-1:2007 Sa 2 1/2 or SSPC SP-10).
- Product Application
- Application Conditions - Shake well before use.
- Mixing - Can thin using conventional thinner. Insulating properties will decrease as dilution occurs.
- Application Method - Airless spray Thinner
- Nozzle pressure - Not less than 10Mpa
- Nozzle Tip - No.163-415~617
- Brush/Roller Thinner - Power mix to loosen paint, apply using Brush roller
- Coats Recommended - 1 - 2
- Although direct two coats application on to steel surface is possible for in door service, blast cleaning to steel surface is required.
- Make sure to protect painted film from dust in case drying time under normal temperature becomes long before high temperature service starts.
- It is not suitable for a strong steam, acid and alkali environment due to poor resistance.
- When over coated, bleeding of undercoat may be observed. The bleeding would stop when a second coat of over coat is applied or by spray application.
Properties
- Color
- Physical Properties
Value Units Test Method / Conditions Finish Flat Finish - - Base Water - Based - - Volume Solids 15.0 % - Typical Thickness of Coat (Dry) 2.0 microns - Theoretical Coverage 300 - 400 sq.ft/gallon - Coats Recommended 1.0 - 2.0 - - Specific Gravity 1.1 - - VOC Low - - Thermal Conductivity 0.1 - 0.04 W/mK - Application Temperature approx. 5.0 - 40 °C - Operation Temperature approx. 55 - 140 °C -
Technical Details & Test Data
- Drying Time
Drying time may vary depending on film thickness, ventilation, humidity, undercoat paint condition etc.
5°C 20°C 30°C Surface Dry 6 Hours 4 Hours 3 Hours Touch Dry 10 Hours 8 Hours 6 Hours - Overcoating Interval
5°C 20°C 30°C Minimum 16 Hours 12 Hours 8 Hours Maximum NA NA NA - Product Comparison
Safety & Health
- Safety Precautions
- Avoid inhalation of spray mist or vapor.
- Avoid skin and eye contact.
- Paint contacted with skin should be immediately removed with water and/or suitable cleanser.
- Eyes should be flushed with water and seek immediate medical attention.
- Since this product contains flammable solvents, keep away from sparks and open flames.
- Application and handling of this product should be in compliance with relevant national regulations.
Storage & Handling
- Storage
- Store in dry, cool condition and away from sources of heat and ignition.
- Containers must be kept tightly closed.
- Store conditions shall be in accordance with national regulations.
- Shelf Life
3 years from manufacturing date.