Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Type
- Non-Slip Epoxy Coating
- Gloss
- Matte / Textured
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
To enhance the traction of potentially slippery walking surfaces, this nonslip coating is suitable for application in industrial settings.
- Oil & gas equipment
- Warehouses & loading docks
- Manufacturing settings
- Concrete or steel walkways
Applications & Uses
- Markets
- Applications
- Application Method
- Compatible Substrates & Surfaces
- Quick Reference
- Mix Ratio - 3:1 (Resin to Catalyst)
- Catalyst - 81000C Billy Grip Catalyst
- Recommended Thickness - 12 - 18 mils
- Theoretical Coverage - 40 - 60 ft2/usg
- Thinner - Do not thin
- Clean-up - Xylene
- Application Guide
- Surface - Steel, Galvanized, Aluminum, Concrete
- Pot Life - 2 hours at 75°F
- Brush or Roller - Apply using a textured roller to achieve desired profile. Use as described within specified pot life.
- Surface Preparation
All surfaces must be clean and free from dirt, oils, rust, flaking paint, and other contaminants. Ensure a sandblast quality of SSPC-SP6 (NACE 2) Commercial blast or for best results SPC-SP10 (NACE 2) Near White blast or better.Proper surface preparation will enhance the performance of the coating system.
Important - Billy Grip should be applied to properly primed surfaces. Exterior / UV exposed applications will result in chalking.
- Application Instructions
- Thinning - Thinning is not recommended. Mix thoroughly before use, A to B ratio is 3:1. Combine 3/4 gallon “A” Billy Grip Non-Slip Epoxy Primer with 1 quart “B” 81000C and mix well.
- Note - This product must be thoroughly mixed before using to ensure uniform application and cure. Mechanical agitation is highly recommended, approximately 3 - 5 minutes. Apply when surface and air temperature are between 35°F - 100°F. Ensure surface temperature is at least 5°F above the dewpoint.
- Drying Time - See application data for typical dry times. Low temperature, high humidity, poor ventilation and thick films will slow drying.
- Clean Up - Clean up paint tools or spills immediately with recommended thinner, carefully observing cautions on paint and thinner labels. Dried paint may be removed by scraping. Always know VOC laws for coating application in your area and follow regulated restrictions.
Properties
- Typical Properties
Value Units Test Method / Conditions VOC (Mixed) 242.2 g/L - Weight Solids (Mixed) 81.51 - 85.51 % - Volume Solids(Mixed) 68.63 - 72.63 % - Viscosity (Mixed) Thixotropic - - Flash Point -19.4 °F -
Technical Details & Test Data
- General Purpose System Specifications
- Sandblast - SSPC-SP6 (NACE 3) Commercial Blast or SSPC-SP5 (NACE 1) Near-white Blast
- Prime - 105FP FerraPrime Epoxy Primer 2.5 - 4.0 mils DFT
- Topcoat - Billy Grip Non-Slip Epoxy 12.0 - 18.0 mils DFT
- Clear Coat (optional) - 500NX - Clear NexShield HS Urethane Topcoat, 1.0 - 2.0 mils DFT
- Total System - 14.5 - 22.0 mils DFT
Safety & Health
- Safety
For industrial use only by professional applicators. Always wear appropriate safety equipment and observe proper handling techniques.
Storage & Handling
- Shelf Life
- 1 Year From Shipment
- Storage
Store in cool, dry, and secure location.