Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Polymer Name
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
- Key Benefits
- Very low moisture absorption
- Finer, cleaner detail possible - excellent machinability
- Very high level of precision possible - low internal stresses
- Good value - an ideal choice for specific application environments
- Competitive Advantage
- Base Resin- Semitron® MP370 uses modified PEEK as a base resin offering higher heat for improved ability to machine clean fine features and improved toughness to resist breakage in use when compared to ceramic filled PEEK materials.
- Processing- Semitron® MP370 uses extrusion to manufacture ultra low stress consistent plate as compared to typical injection molded ceramic filled materials. Extruded material provides far better dimensional stability during machining allowing for finer features while maintaining tighter tolerances.
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Product Applications
- IC test sockets for semiconductor manufacturing equipment
- Structural parts in electronics and telecom equipment
- Insulating blocks and fixtures in diagnostic equipment
Properties
- Color (Properties)
- Flame Rating
- Physical Form
- Mechanical Properties
Value Units Test Method / Conditions Tensile Strength 78 MPa ISO 527-1/-2 (7) Tensile Strain (Elongation) at Break 2 % ISO 527-1/-2 (7) Tensile Modulus of Elasticity 4450 MPa ISO 527-1/-2 (9) Shear Strength 78 MPa ASTM D732 Compressive Stress (1 / 2 / 5 % Nominal Strain) 38/72 MPa ISO 604 (10) Charpy Impact Strength (Unnotched) 50 kJ/m² ISO 179-1/1eU Charpy Impact Strength (Notched) 4 kJ/m² ISO 179-1/1eA Hardness (14) 97 Rockwell M ISO 2039-2 - Thermal Properties
Value Units Test Method / Conditions Melting Temperature (DSC, 10°C (50°F) / min) 340 °C ISO 11357-1/-3 Thermal Conductivity (23°C) 0.34 W/(K.m) - Coefficient of Linear Thermal Expansion (23 - 60°C) 49 µm/(m.K) - Coefficient of Linear Thermal Expansion (23 - 100°C) 51 µm/(m.K) - Coefficient of Linear Thermal Expansion (min. 150°C) 109 µm/(m.K) - Heat Deflection Temperature (Method A: 1.8 MPa (264 PSI)) 148 °C ISO 75-1/-2 Flammability (3 mm) (5) V-0 - UL 94 - Electrical Properties
Value Units Test Method / Conditions Surface Resistivity 10000000000000 Ohm/sq. ANSI/ESD STM 11.11 - Miscellaneous Properties
Value Units Test Method / Conditions Density 1.65 g/cm³ ISO 1183-1 Water Absorption (At Saturation in Water of 23 °C) 0.5 % -
Regulatory & Compliance
- Certifications & Compliance
- Chemical Inventories
Technical Details & Test Data
- Engineering Notes
It is important to know how applied voltage affects the resistance of a material. Some materials exhibit high resistance at low voltages, but when subjected to harsher conditions, they can fall. This is due to dielectric breakdown and is irreversible. This chart illustrates the effect of sequential applications of 100 through 1,000 volts, then a return to 100 volts to determine the hysteresis. Since static electricity can be several thousand volts, consistent performance across the voltage range must be considered.
Some materials are very inconsistent and vary on the "grain" of machining. One pair of lines illustrate the typical variation from side to side (A to B) of the same sample. This example demonstrates the need for consistent behavior in service.
- Base Resin Comparison
- Note
- Thermal Properties - The figures given for these properties are for the most part derived from raw material supplier data and other publications.
- (2) Values for this property are only given here for amorphous materials and for materials that do not show a melting temperature (PBI, PAI & PI). DMA settings, oscillation
- the amplitude of 0.20 mm; a frequency of 1 Hz; heating rate of 2°C/min
- (3) Temperature resistance over a period of min. 20,000 hours. After this period of time, there is a decrease in tensile strength – measured at 23 °C – of about 50 % as compared with the original value. The temperature value given here is thus based on the thermal-oxidative degradation which takes place and causes a reduction in properties. Note, however, that the maximum allowable service temperature depends in many cases essentially on the duration and the magnitude of the mechanical stresses to which the material is subjected.
- (4) Impact strength decreasing with decreasing temperature, the minimum allowable service temperature is practically mainly determined by the extent to which the material is subjected to impact. The value given here is based on unfavorable impact conditions and may consequently not be considered as being the absolute practical limit.
- (5) These estimated ratings, derived from raw material supplier data and other publications, are not intended to reflect hazards presented by the material under actual fire conditions. There is no ‘UL File Number’ available for these stock shapes.
- Mechanical Properties - Most of the figures given for the mechanical properties are average values of tests run on dry test specimens machined out of rods 40-60 mm when available, else out of plate 10-20mm. All tests are done at room temperature (23° / 73°F)
- (7) Test speed: either 5 mm/min or 50 mm/min [chosen acc. to ISO 10350-1 as a function of the ductile behavior of the material (tough or brittle)] using type 1B tensile bars
- (8) Test speed: either 0.2"/min or 2"/min or [chosen as a function of the ductile behavior of the material (brittle or tough)] using Type 1 tensile bars
- (9) Test speed: 1 mm/min, using type 1B tensile bars
- (10) Test specimens: cylinders Ø 8 mm x 16 mm, test speed 1 mm/min
- (11) Test specimens: cylinders Ø 0.5" x 1", or square 0.5" x 1", test speed 0.05"/min
- (12) Test specimens: bars 4 mm (thickness) x 10 mm x 80 mm; test speed: 2 mm/min; span: 64 mm.
- (13) Test specimens: bars 0.25" (thickness) x 0.5" x 5"; test speed: 0.11"/min; span: 4"
- (14) Measured on 10 mm, 0.4" thick test specimens.
- (15) Electrode configuration: Ø 25 / Ø 75 mm coaxial cylinders; in transformer oil according to IEC 60296 ; 1 mm thick test specimens.
- (16) Measured on disks Ø 50 mm x 3 mm.
- (17) Measured on 1/8" thick x 2" diameter or square
- (18) Test procedure similar to Test Method A: “Pin-on-disk” as described in ISO 7148-2, Load 3MPa, sliding velocity= 0,33 m/s, mating plate steel Ra= 0.7-0.9 μm, tested at 23°C, 50%RH.
- (19) Test using journal bearing system, 200 hrs, 118 ft/min, 42 PSI, steel shaft roughness 16±2 RMS micro inches with Hardness Brinell of 180-200
- (20) Test using Plastic Thrust Washer rotating against steel, 20 ft/min and 250 PSI, Stationary steel washer roughness 16±2 RMS micro inches with Rockwell C 20-24
- (21) Test using Plastic Thrust Washer rotating against steel, Step by step increase pressure, Test ends when plastic begins to deform or if temperature increases to 300°F.