Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Fillers Included
- Polymer Name
- Reinforcement Material
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
- Properties
- Very high mechanical strength
- Very high rigidity (also at low temperature)
- Very high thermal stability
- Very high creep resistance
- Very high dimensional stability
- Very high radiation resistance
- Very high hydrolysis resistance
- Relatively low notch impact strength
- Low resistance to acetone
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
- Applications
- Locking devices
- spacers
- flanges
- fixtures in glass production
Properties
- Color
- Flame Rating
- Physical Form
- Form and Condition
- Rods. Sheets / Solid
- Odor
- Odorless
- Insoluble in
- Water
- Mechanical Properties
Value Units Test Method / Conditions Tensile Strength at Yield 115 MPa ISO 527 Tensile Strength at Yield 105 MPa ISO 527 Elongation at Yield (S) 3 % ISO 527 Tensile Strength at Break 180 MPa ISO 527 Elongation at Break (R) 2.7 % ISO 527 Impact Strength (an) 32 kJ/m2 ISO 179 Notch impact Strength (ak) 8 kJ/m2 ISO 179 Ball Indentation (Rockwell Hardness) 315 MPa ISO 2039 Hardness 90 Shore D ISO 868 Flexural Strength (B 3,5 %) 164 MPa ISO 178 Modulus of elasticity (Et) 6380 MPa ISO 527 - Physical Properties
Value Units Test Method / Conditions Specific Gravity 1.51 - ISO 1183 Water Absorption 0.3 % ISO 62 Humidity Absorption 0.04 % ISO 62 Maximum Permissible Service Temperature 260 °C UL746B - Thermal Properties
Value Units Test Method / Conditions Heat Deflection Temperature (HDT/A) 328 °C ISO 75 Coefficient of Linear Thermal Expansion 0.38 K-1.10-4 ISO 11359 Thermal Conductivity (20°C) 0.35 W/(m.K) ISO 22007-4 Glass Transition Temperature (Tg) 147 °C ISO 3146 Melting Temperature (Tm) 341 °C ISO 3146 - Typical Properties
Value Units Test Method / Conditions Density 1.30 - 1.55 g/cm³ - Melting Temperature min. 330 °C - Ignition Temperature min. 590 °C - - Electrical Properties
Value Units Test Method / Conditions Volume Resistivity min. 10^13 Ω.cm IEC 60093 Surface Resistivity (Ro) min. 10^13 Ω IEC 60093 Dielectric Constant (1MHz) 3.2 - IEC 60250 Dielectric Loss Factor (1 MHz) 5 - IEC 60250 Dielectric Strength 20 kV/mm IEC 60243-1 - Additional Information
Value Units Test Method / Conditions Bondability Yes - - Physiological Indifference Yes - EEC Flammability V-0 - UL 94 Limiting Oxygen Index (LOI, 9) 43 % ASTM D2863 UV Stabilisation (6, 9) Limited - -
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Fire-fighting Measures
Suitable extinguishing agents
Water, foam, dry chemical, carbon dioxide (CO2).
Potential combustion products
Carbon dioxide (CO2), carbon monoxide (CO). Formation of further decomposition and oxidation products depend upon the fire conditions. Under special fire conditions traces of other toxic substances are possible.
Special protective equipment
Wear a self-contained breathing apparatus. If exposed to combustion fumes bring the victim into fresh air.
Further information
Dispose of fire debris and contaminated extinguishing water in accordance with official regulations..
Safety & Health
- Safety Measures
The general industrial safety measures should be considered. A thermal damage during machining should be avoided.
Storage & Handling
- Machining
The product can be machined with standard machinery and tools. Before machining the product should be stored at room temperature 24 h. Evacuate swarf to prevent slipping or tripping. Observe the maximum allowable concentration of dust and formaldehyd levels on the working area which apply in your country. Wear safety goggles during machining. General dust limit value: Respirable dust (6 mg/m3); Inhalable dust (10 mg/m3 ).
- Storage
The products shall be stored indoor to keep away from any source of degradation such as sunlight, UV-jets, ionizing radiation, chemicals.