Search
the marketplace
through 230,000 Chemicals and Raw Ingredients
through 8,000+ Supplier owned storefronts

EPOXICAST™ 1106F-LD

EC-1106F-LD is a low viscosity, easily pourable, epoxy syntactic foam. It features low density, good electrical insulation, and low shrinkage during cure. It is useful for potting and encapsulating components and modules where added weight is undesired but resistance to mechanical and thermal shock are prime considerations. Typical Applications includes potting or encapsulating densely packaged power supplies, integrated circuits, small transformers, capacitors bushings etc.

Brand: EPOXICAST (8 products)

Foam Type: Syntactic Foam

Density: 749.136 - 749.136 kg/m³

Chemical Family: Epoxy & Epoxy Derivatives

End Uses: Capacitor Bushings, Integrated Circuits, Power Transformers

Technical Data Sheet

Enhanced TDS

Knowde-enriched technical product data sheet

Identification & Functionality

Chemical Family
Epoxy & Epoxy Derivatives
Foam Type
Syntactic Foam
Product Type
Foam
Technologies
Ready-to-Use Products
Product Families
Ready-to-Use Products — Foams

Features & Benefits

Ready-to-Use Product Features
Electrically Insulating,
Flexible,
Good Mechanical Properties,
Good Thermal Conductivity,
Low Density,
Low Shrinkage,
Low Viscosity,
Pourable,
Thermal Shock Resistant,
Thermally Conductive

Applications & Uses

Markets
Electrical & Electronics
Applications
Electrical & Electronics — Parts & Components
Printed Circuit Boards (PCBs)
Electrical & Electronics — Wire & Cable
Power Transmission & Distribution
Product End Uses
Capacitor Bushings,
Integrated Circuits,
Power Transformers
Instruction for Use

Stir well the contents of each container every time before removing material. If the contents are hard or lumpy, warm to 80°C and mix thoroughly before removing material.

1. Weigh each 100 grams of PART-A to 18 grams of Hardener PART-B
2. Mix until uniform. Scrape the sides and bottom of container repeatedly during mixing.
3. Proceed with potting application. Vacuums degas and cure as recommended to achieve the desired properties.
4. Typical cured properties were determined using recommended cure schedule. Some difference in properties may occur with the alternate or other cure schedules.

Industrial Usage

Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.

Properties

Color
Black
Typical Properties
ValueUnitsTest Method / Conditions
Compound Viscosity (at 25°C)10,000 - 20,000cPs-
Mixed Viscocity (at 25°C)4000 - 8000cPs-
Pot Life (at 25°C, 100g)2hours-
Recommended Cure (at 100°C)1 - 2hours-
Alternate Cure (at 25°C)24 - 48hours-
Typical Cured Properties
ValueUnitsTest Method / Conditions
Specific Gravity0.75--
Hardness85Shore D-
Linear Shrinkage0.31%-
Water Absorption (24 hr at Room Temperature)0.2%-
Thermal Conductivity 0.2W/m °K-
Glass Transition Temperature (Tg)28°C-
Dielectric Strength480Volts/mil-
Dielectric Constant (at 1 kHz)2.8--
Dielectric Constant (at 1 MHz)2.3--
Dissipation Factor (at 1 kHz)0.14--
Volume Resistivity1x10^14Ω-cm-

Safety & Health

Warning

Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention.

Packaging & Availability

Available Packaging

2 parts Kit - Packaged in Gallon, and 5-Gallon size.