Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features
- ISO-10993-5 tested for cytotoxicity
- NASA Outgassing Tested
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Compatible Substrates & Surfaces
- Cure Method
- Applications
- Epoxy adhesive used for endoscopes, catheters, and ultrasound probes
- Field Assembly
- Mix and cure in the field.
- Optics
- Active alignment of optics such as lenses, prisms, diodes, filters, etc. to opto-circuit
- Fiber Optics
- “field curing” or field assembly of connectors and couplers
- Also suggested for fiber optic splicing
- Medical
- Adhesion to most metals, plastics, ceramics, and glasses found in tubing, substrates or housing.
- Instructions for Use
To use simply insert the cartridge into the application gun and start the plunger into the cylinders using light pressure on the trigger. Next, remove the cartridge cap and expel a small amount of adhesive to be sure both sides are flowing evenly and freely. If automatic mixing of resin and hardener is desired, attach the mixing nozzle to the end of the cartridge and begin dispensing the adhesive. For hand mixing, expel the desired amount of the adhesive and mix thoroughly. Mix approximately 15 seconds after uniform color is obtained.
Properties
- Typical Cured Properties
Value Units Test Method / Conditions Specific Gravity 1.1 - - Hardness 86 Shore D - Lap Shear Strength to Aluminium (at -55°C) 2300 psi - Lap Shear Strength to Aluminium (at 25°C) 3100 psi - Lap Shear Strength to Aluminium (at 95°C) 150 psi - Die Shear Strength 1800 psi - Refractive Index 1.5482 - - Service Temperature Range -55 to 125 °C - Glass Transition Temperature (Tg) 72 °C - Coefficient of Linear Thermal Expansion (Below Tg) 62 10⁻⁶/°C - Coefficient of Linear Thermal Expansion (Above Tg) min. 200 10⁻⁶/°C - NASA Outgassing Data (TML) 0.59 % - NASA Outgassing Data (WVR) 0.21 % - NASA Outgassing Data (CVCM) 0.06 % - Dielectric Strength 508 Volts/mil - Dielectric Constant (at 1 kHz) 3.2 - - Dissipation Factor (at 1 kHz) 0.02 - - Volume Resistivity 1x10¹³ ohm-cm - - Handling Properties
Value Units Test Method / Conditions Mix Ratio by Volumet (Resin/Hardener) 2:1 - - Mixed Viscosity (at 25°C) 4,000 - 7,000 cps - Pot Life (at 25°C, 100 grams) 30 hours -
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Curing Information
- Recommended Cure : 3 hours at 65°C
- Alternate Cure : 24 hours at 25°C
Safety & Health
- Safety Information
- For Industrial Use Only : These materials are intended for industrial use only, and the practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning : Adequate ventilation of workplace and ovens is essential. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet for additional health and safety information.
Packaging & Availability
- Packaging Type
Storage & Handling
- Shelf Life
- 12 Months
- Storage & Shelf Life
Product shall be ideally stored in a dry location in unopened containers at a temperature between 20°C to 28°C unless otherwise labeled. The shelf life of these materials is 12 months when stored in unopened containers at an average temperature of 25°C.