Concrete Sealers PS111

• Acts as curing aid
• Densifies & hardens
• Improves durability
• Lowers maintenance
• Decreases dusting
• Increases surface strength
• Enhances abrasion resistance
• Maintains traction

• Professional grade
• One step application
• Dries flat & clear

PS111 was originally developed for commercial and industrial applications and is widely used throughout North America to this day for those applications. Concrete Sealers USA is now also making this professional grade sealer available to the residential market so small contractors, applicators, and do-it-yourselfers can enjoy the same superior benefits that architects, engineers, and large contractors have enjoyed for years. PS111 is recommended as a curing aid and hardener for smooth troweled or broom finished surfaces. It is ideal for curing newly placed concrete such as parking lots and structures, marine structures, loading docks, median barriers, bridge decks, concrete pavement, piers, ramps, plazas, courtyards, and balconies. It is also recommended for workshop floors, warehouse floors, automotive garage floors, retail store floors, pole barn and shed floors, basement floors, garage floors, driveways, sidewalks, walkways, porches, pool decking, and patios. It is suitable for horizontal or vertical and interior or exterior applications. Compatible with glues, mastics, topical coatings, and penetrating sealers.

The surface must be porous enough to allow penetration into the substrate. For fresh concrete, surfaces should be clean, dry, free of bleed water, final finishing process completed, and sufficient strength to be stood on without being marred. Added benefits can be obtained by waiting 3-7 days after placement when peak hydration and off gassing have slowed enough to allow better penetration of the curing aid into the substrate. Surfaces should not be burnished or polished prior to application. PS111 can be applied to bull floated surfaces, broom finished surfaces, and unburnished smooth troweled surfaces. For existing concrete, surface should be free of surface laitance, dust, dirt, debris, mildew, oil, grease, previous sealers, curing agents, paint or other surface coatings, and other contaminants.

Always test porosity prior to application, especially on very dense surfaces. Surface should be dry for proper penetration of the sealer. Should not apply to damp or wet surfaces or if rain is expected within 12 hours after application. Product is a one part system and requires no special mixing. Stir material thoroughly before and during application. Do not apply below 40°F or above 95°F during the application or drying period. Apply uniformly with a low pressure sprayer. When applying the material, work in small, manageable areas at a time in order to maintain a wet edge. The PS111 should be applied in an overlapping or circular pattern to ensure areas are not missed. Apply material to the point of rejection and ensure it is fully absorbed within 10 minutes without puddles. Areas of greater porosity may require application of more PS111 but only apply additional material as needed. Use a soft bristled broom or microfiber pad to evenly distribute product as well as disperse any puddles or excesses. Do not allow excesses to dry on a surface. Excesses can result in a gel or white residue on surface but it can normally be easily removed by flushing with clean water and use of a stiff bristled broom. Generally, only one application is required. If additional coats are desired and more product can be absorbed, wait approximately 1-2 hours between coats or until previous application has dried fully. Clean application materials with warm water.

PS111 is designed to work only on uncolored and unsealed freshly placed interior or exterior smooth troweled or broom finished surfaces and is not intended for asphalt. Concrete must be allowed to cure a minimum of 28 days prior to allowing topical coatings, adhesives, or water repellents. This product may damage vegetation or may etch glass, aluminum, and metal. Avoid contact with eyes and skin. Sealer may be damaged if frozen prior to use. Membrane forming curing agents may be more appropriate in extremely hot, low humidity, or high wind weather conditions or when specific curing requirements need to be satisfied.

• Warehouse floors
• Workshop floors
• Garage floors
• Pole barn & shed floors
• Driveways
• Sidewalks
• Patios

• 300-500 sq. ft./gal. for smooth troweled and 200-300 sq. ft./gal. for broom finished surfaces

Shipping:

• Normal package delivery and trucking