Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Key Features
- UL recognized in file No. E334038
- Good thermal conductivity
- Non corrosive
- Fast skinning
Applications & Uses
- Markets
- Applications
- Application Area
- Application Method
- Cure Method
- Use and Cure Information
- This product is a ready for use 1 Part system. If supplied in cartridges it can be applied using either manual or pneumatic dispensing guns. It can also be applied from bulk containers using conventional drum dispensing equipment.
- All surfaces to which the sealant is to be applied should be clean, dry and free from grease, dirt, and loose material. Priming of surfaces is not normally required. If using as an adhesive, it should be applied to one clean surface and the other clean surface brought into contact with it within the tack free time stated opposite. For optimum bond strength, the thickness of the sealant joint should be a minimum of 1 mm.
- The sealant will cure upon exposure to atmospheric moisture, ideally between 20 to 30 ºC and 40% to 70% Relative Humidity. Time taken for cure will depend on the thickness of the joint, humidity and temperature. Joints should be left undisturbed for at least 24 hours, but preferably longer to effect sufficient depth of cure. Full cure requires 7 days.
- “For pneumatic dispensing of 310 ml cartridges, the recommended pressure is 2.25 to 3.45 bar (40 to 50 psi). Dispensing pressure above the recommended limits may lead to gas bypassing the piston, causing spluttering at the nozzle and poor bead quality”
Properties
- Flame Rating
- Physical Form
- Electrical Properties
Value Units Test Method / Conditions Dielectric Constant 4.9 - ASTM D- 150 Dielectric Strength 39.0 kV/mm ASTM D- 149 Dissipation Factor 0.009 - ASTM D- 150 Volume Resistivity 1.00 x 10¹⁴ Ω.cm ASTM D- 257 - Adhesion Properties
Value Units Test Method / Conditions Lap Shear Aluminium 6.0 kg/cm² ASTM D1002 Lap Shear Copper 3.0 kg/cm² ASTM D1002 Lap Shear Stainless Steel 2.6 kg/cm² ASTM D1002 - Cured Properties
Value Units Test Method / Conditions 100% Modulus 0.5 MPa - Density 2.24 g/cm³ BS ISO 2781 Elongation (at Break) 94.0 % ISO 37 Hardness Shore A 65.0 - ASTM D 2240-95 Linear Coefficient of Thermal Expansion 198.0 ppm/°C - Linear Shrinkage 1.0 % - Working Temperature Range -50 - 220 °C - Tensile Strength 2.8 N/mm² ISO 37 Thermal Conductivity 1.55 W/mK - UL File Number E334038 - - Volume Coefficient of Thermal Expansion 475.0 ppm/°C - Youngs Modulus 0.4 N/mm² - - Uncured Properties
Value Units Test Method / Conditions Cure Through to 3 mm Depth 8.0 Hours - Tooling Time (at 23°C) 4.0 - - - Note
Cured properties are tested after 7 days at 23 (+/-2)°C and 50(+/-5%) humidity
- Uncured Product Property
Property Key Value Cure Profile 23+/-2°C and 50+/-5% humidity
Cure Type Acetone Rheology Paste Self Bonding Yes
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Packaging Type
- Packaging
- CHT Adhesives are available in a variety of packaging including cartridges and bulk containers.
- Users are advised to carry out their own tests on clean, degreased substrates to ensure satisfactory adhesion is achieved.
- Stress cracking can appear on some grades of polycarbonate and poly(methyl methacrylate). Users are advised to carry out initial testing to ensure product compatibility.
Storage & Handling
- Storage and Shelf Life
- Maximum storage temperature is 40 °C / 104 °F.
- Shelf Life : 9 months in cartridges, 12 months in pails