Enhanced TDS
Knowde-enriched technical product data sheet
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Applications
- Application Method
- Applications
- Mixing: Stir thoroughly, making sure no pigment remains on the bottom of the can.
- Thinning: This coating is VOC compliant; only thin if permitted by federal, state and local regulations. If necessary, use Anchor #J1131 for spray applications and #J1112 for brush and roller requirements.
Application Equipment
- Roller: Use 1/4" synthetic nap covers.
- Brush: Use high quality natural china bristle brushes.
The recommended method of application is by airless spray. However, brush, roller, or conventional spray may also be used. To avoid dusting, apply in wet coats. On a derusted surface, the application of a dry film thickness of at least 2 mils is recommended. With any oxidative coating, faster dry time may be obtained with increased air movement and/or higher substrate or material temperature.
Application: Use with J1100 Urethane Catalyst
When used with Anchor J1100 Urethane catalyst; an 8:1 ratio is used; the optimal blend is 8 parts of Saf-TGard II 900 series enamel and 1 part of J1100. In actual use this is one gallon of the 900 series Saf-T-Gard II enamel and a pint of J1100.
The following table gives the expected dry times associated with application
All time in Hours 900 w/o J1100 900 w/8:1 J1100 Added
Dry to Touch 3.5 2.5 Tack Free 5 4.5 Dry Through 24 24 Cleanup
Use Anchor #J1131 or #J1112
Where to Use
This product is a heavy-duty enamel designed for architectural and industrial maintenance applications.
Preparation & Priming
Surface Preparation
For maximum performance, the recommended substrate should be blasted in accordance with SSPC-SP7. If blast cleaning is not feasible, the substrate should be degreased in accordance with SSPC-SP1. All burrs should be removed and sharp edges or rough weld seams should be ground down. Full use should then be made of mechanical power tools, in conjunction with wire brushing and chipping to remove all loose rust and mill scale to a standard of cleanliness conforming to SP-2 or SP-3. Prior to painting, all dust should be removed from the substrate by using clean brushes and/or dry compressed air.
Primer Coats
Typically, Anchor #1600 Series Rust Inhibitive Primers are recommended.
Properties
- Typical Properties
Value Units Test Method / Conditions Surface Temperature 50 - 110 ° F - Recommended Thickness (Mils Dry Per Coat) 1.6 - 2.0 - - Theoretical Coverage (1 Mils Dry) 869.0 ft²/gallon - Coverage Rates per Coat (Dry Mils) 1.8 - - Coverage Rates per Coat (Wet Mils) 3.3 - - Coverage Rates per Coat 483.0 Ft²/gal - Airless Spray (Pressure) 1200 - 2200 psi - Conventional Spray (Air Pressure) 40 - 70 psi - Conventional Spray ( Fluid Pressure) 10 - 20 psi - Finish High Gloss - - Solids by Volume 54.9 % - Architectural and Industrial Maintenance Category Non-Flat Coatings, Exterior - - AIM Category VOC Limitt 380.0 g/l - Actual VOC 372.0 g/l - Density 372.0 g/l - Storage Temperature 20 - 110 ° F - Chemical Resistance (Alkalis) Fair - -
Technical Details & Test Data
- Performance Data
Substrate: Steel
Surface Preparation: SSPC-SP10
System Tested: 1 coat 0900 Saf-T-Gard II White or 1 coat 0900 Saf-T-Gard II White with J1100 Urethane Converter (8:1)
Test Name Test Mothod 900 0900 +J1100 QUV ASTM D-4587 312 Hours Retain 31.5% 20° Gloss and 69% 60 Gloss Retain 61% 20° Gloss and 84% 60 Gloss
Salt Fog Resistance ASTM B117 250 Hours 225 Hrs Hardness (Penci) ASTM D 3363 4B HB Adhesion (Pulloff) ASTM D 4541 150 PSI 100 PSI Adhesion (Crosshatch) ASTM D 3359 4B |4B Direct Impact ASTM D-2794 50 inch/pounds 10 inch/pounds
Safety & Health
- Safety Information
- Danger Flammable liquid and vapor. Vapor harmful. Contains: mineral spirits and n-butyl acetate. Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Causes nose, eye, skin and throat irritation. Harmful if swallowed. Notice: reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.
- Keep away from heat, sparks and flame. Vapors may cause flash fire. Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources or ignition during use and until all vapors are gone. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (niosh approved) during and after application. Follow respirator manufacturer’s directions for respirator use. Do not get in eyes, on skin or clothing. Wash thoroughly after handling. Keep out of reach of children.
- If you scrape, sand or remove old paint, you may release lead dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as brain damage, especially in children. Pregnant women should also avoid exposure. Wear a niosh-approved respirator to control lead exposure. Clean up carefully with a hepa vacuum and a wet mop.
Packaging & Availability
Storage & Handling
- Shelf Life
- 2 Years Under Normal Conditions (Unopened)
- Storage Temperature
Minimum 20°F & Maximum 110°F