Products in Engineering & Specialty Polymers: Cable Extrusion

8 Products found in Engineering & Specialty Polymers

Browse Applications

EvonikVESTAMID® L1670

Polymer Name:Polyamide 12 (PA 12)
Processing Methods:Cable Extrusion, Injection Molding, Profile Extrusion, Wire Extrusion, Extrusion
Additives Included:Lubricant (Unspecified), UV Stabilizer, Processing Aid, Light Stabilizer, Heat Stabilizer
Flexural Modulus:1350.44 - 1350.44 MPa
Materials Features:Rodents Resistant, Low Water Absorption, Good Tenacity, Low Coefficient of Friction, Light Stabilized, Very Good Heat Resistance, Lubricated, Chemical Resistant, Low Viscosity, Dimensional Stability, Unreinforced, Semi Crystalline, Heat Stabilized, UV Stabilized, Termites Resistant
Color:Natural

VESTAMID® L1670 is a low-viscosity polyamide 12 compound that has been specifically developed with heat and light stabilization for the extrusion of thin wire insulations and cable jacketings. Coatings made from VESTAMID® L1670 demonstrate a low coefficient of friction, which greatly facilitates the process of laying cables. This compound is well-suited for profile extrusion and wire and cable extrusion processing techniques.

Fluoropolymer Resources LM FEP (02.001.09.00,clear) banner

Fluoropolymer ResourcesFluoropolymer Resources LM FEP (02.001.09.00,clear)

Polymer Name:Perfluoroethylene Propylene Copolymer (FEP)
Labeling Claims:Recycled, Contains PIR Resin, Contains PCR Resin
Processing Methods:Film Extrusion, Extrusion, Cable Extrusion
Density:2120.0 - 2170.0 kg/m³

FEP LM is used for higher speed extrusion of wire and cable jackets, tubing, or film.

Fluoropolymer Resources LMPLUS FEP (02.001.09.00,clear) banner

Fluoropolymer ResourcesFluoropolymer Resources LMPLUS FEP (02.001.09.00,clear)

Polymer Name:Perfluoroethylene Propylene Copolymer (FEP)
Labeling Claims:Recycled, Contains PIR Resin, Contains PCR Resin
Processing Methods:Film Extrusion, Extrusion, Cable Extrusion
Density:2120.0 - 2170.0 kg/m³

FEP LMPLUS higher speed extrusion of wire and cable jackets, tubing, or film.

Fluoropolymer Resources LML FEP (02.001.09.00,clear) banner

Fluoropolymer ResourcesFluoropolymer Resources LML FEP (02.001.09.00,clear)

Polymer Name:Perfluoroethylene Propylene Copolymer (FEP)
Labeling Claims:Recycled, Contains PIR Resin, Contains PCR Resin
Processing Methods:Extrusion, Cable Extrusion
Density:2120.0 - 2170.0 kg/m³

FEP LML is used for injection molding; thin-walled wire and cable or tube extrusion.

Badamid® PA12 H banner

Bada AGBadamid® PA12 H

Polymer Name:Polyamide 12 (PA 12)
Processing Methods:Cable Extrusion, Injection Molding
Additives Included:Heat Stabilizer
Flexural Modulus:1500.0 - 1500.0 MPa

Badamid® PA12 H by Bada AG is comprised of Polyamide 12. It is commonly used It is available in Granules form.

Nylene® NX4795 banner

NyleneNylene® NX4795

Polymer Name:Polyamide 6 (PA 6)
Processing Methods:Extrusion, Cable Extrusion
Additives Included:Heat Stabilizer, Lubricant (Unspecified), Slip Agent

Nylene Heat stabilized, lubricated nylon 6 intended for use in coating wire, usually extrusion coated over a layer of PVC on electrical wires for toughness, temperature resistance, and insulating properties, and contains a high slip additive for ease of use when pulling wire through conduit. Delivered dry, with less than 0.2% moisture, and can be extruded as received.

Fluoropolymer Resources LMLPLUS FEP (02.001.09.00,clear) banner

Fluoropolymer ResourcesFluoropolymer Resources LMLPLUS FEP (02.001.09.00,clear)

Polymer Name:Perfluoroethylene Propylene Copolymer (FEP)
Labeling Claims:Recycled, Contains PIR Resin, Contains PCR Resin
Processing Methods:Extrusion, Cable Extrusion
Density:2120.0 - 2170.0 kg/m³

FEP LMLPLUS injection molding; thin-walled wire and cable or tube extrusion.

Nylene® 603 banner

NyleneNylene® 603

Polymer Name:Polyamide 6 (PA 6)
Processing Methods:Extrusion, Cable Extrusion
Additives Included:Plasticizer (Unspecified)

Nylene Plasticized, high residual monomer resin designed for extrusion applications requiring excellent flexibility, high strength and good abrasion resistance Applications include flexible tubing, cable jacketing, and mono-filament extrusion such as fish line and netting, sewing thread, and weaving thread Optimum processing conditions should permit for a melt temperature of approximately 450°F at the die.