Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
Applications & Uses
- Markets
- Application Area
- Compatible Substrates & Surfaces
- Cure Method
- Surface Preparation
Steel surfaces are to be abrasive blasted with chloride free abrasive. Exterior applications to SSPC SP-10 Near White metal finish. Immersion applications to SSPC SP-5 White metal 4+ mil profile. Grind flat all burrs, weld seams, radius sharp edges. Fresh blasted ferrous surfaces to be primed with S-20 immediately to prevent oxidation of surface.
Concrete surfaces should be degreased if oil and grease contamination is present. Degreased surface shall be high pressure washed, acid etched, and high pressure washed again so surface is clean and free of all grease, oils and surface laitance. Existing coatings should be abrasive blasted to clean concrete. Prime with EE-10.
- Mixing
Thoroughly mix Activator into Base with mixing stick or drill with low speed mixing blade scraping sides and bottom of container or mixing board. Mix by Volume 2-parts Base to 1-part Activator. Or by weight 100 grams Base to 50 grams Activator. Mix thoroughly to produce an even colored and streak-free material.
- Application
Brush: medium to stiff bristle of sufficient quality that bristles do not pull out and stick in coating. Trim or tape to <1” nap. Roller: good quality 1/8” nap.
ARCOR Cartridge Sprayer: Heat to 140F(60C). Piston ‘3’; Tip Air ‘3’.
Plural Spray: 0.029-.035 RAC tip, 3,000-4,500 PSI, Heat to 160ºF Base, 120ºF Activator. Ambient Temperature and Humidity will affect temperature and pressure setting. Consult ARCOR.
Airless Spray: 0.029-.035 RAC tip, 4,500-5,500 PSI(60:1+). Recommended in-line heater at 120º to 135ºF (Caution: Short Pot-Life). Ambient Temperature and Humidity will affect temperature and pressure setting. Contact ARCOR.
All spray equipment should employ traps to prevent water and oil from contaminating coating and screens to prevent particulate contamination.- Application Temperature
- Keep between 55 to 95ºF (17 to 35ºC). Substrate: Keep between 45 to 105ºF (7 to 40ºC). The difference in temperature of the substrate and the material should never exceed 10ºF(5ºC). Substrate shall be a minimum of 5ºF(3ºC) above dew point. Do not apply if relative humidity exceeds 90%. If necessary, heat metal prior to surface preparation using electric heater or heat lamp. Never use gas, oil or kerosene heaters as they will leave a greasy residue on metal surface. For best results keep all material in warm area overnight (75ºF+, 24ºC) for ease of mixing. If necessary, base component of material can be heated by microwave for 30-45 seconds for a 1 KG Base unit. If necessary, let material cool before application to allow for more pot life during application.
- Overcoat / Cure Time
- By brush, roller or squeegee recoat while material is still soft, but tack-free, between 3-12 hours at 77ºF(25ºC). IMPORTANT: If overcoat window is exceeded abrade surface with course sandpaper, grinder or brush blast and wipe with MEK or Acetone. By spray application recoat between 2-12 hours at 77ºF(25ºC). Full cure before immersion recommended 72 hours at 77ºF(25ºC). Add 1 hour’s additional cure time for each 10ºF(-12.2ºC) below 77ºF(25ºC). For highly aggressive environments Force Cure with heat for best performance for 8 hours at 150ºF (66ºC), 2 hours at 250ºF (121ºC).
- Clean Up
Clean tools immediately after use with M.E.K., Acetone, 98+% Isopropyl Alcohol or similar
Properties
- Temperature Properties
- Specifications
- Note
Coverage:1mil = 25 micron; 1 Gal = 3.785 L; 10.77ft2 = M2
- Chemical Resistance
Water Excellent Alkalis Good Inorganic Acids Good Organic Acids Fair Organic Solvents Good - Film Thickness
- Spray Application: 1-Coat 20 to 40 mils
- Hand Application: 2-3 Coats 15-20 mils per coat
- Final DFT Specified by Need: Consult ARCOR
- Flexibility
Very Good. Excellent with Polyester or Fiberglass Mat; 1.5 oz/ft2 (.5 KG/M2)
- Mix Ratio
2:1 by Volume (Base : Activator) 100 gm : 50 gm by weight
| Value | Units | Test Method / Conditions | |
| Maximum Temperature for Immersion Service | 121.0 | °C | - |
| Temperature Spike Tolerance for Immersion Service (3hrs) | 177.0 | °C | - |
| Recommended Force Cure Temperature (2hrs) | 121.0 | °C | - |
| Maximum Temperature for Dry Heat | 204.0 | °C | - |
| Temperature Spike Tolerance for Dry Heat (3hrs) | 260.0 | °C | - |
| Value | Units | Test Method / Conditions | |
| Pot Life (at 72°F) | 20.0 | min/gal | - |
| Coverage (at 1604/mils) | 1.0 | ft² / gal / coat | - |
| Coverage (at 149/mils) | 1.0 | m²/gal | - |
| Coverage (at 3785/microns) | 1.0 | m²/gal | - |
| Solid Content | 100.0 | % Volume | - |
Packaging & Availability
- Weight Per Gallon
- 12.6 lbs. (5.7 KG)
- 3.3 lbs. (1.5 KG)/Liter
Storage & Handling
- Shelf Life
- 5 Years (at 13-35ºC)